Based on data on the composition of ore-bearing hydrothermal solutions and parameters of ore-forming processes at various antimony and antimony-bearing deposits, which were obtained in studies of fluid inclusions in ore minerals, we investigated the behavior of Sb(III) in the system Sb–Cl–H2S–H2O describing the formation of these deposits.
We also performed thermodynamic modeling of native-antimony and stibnite dissolution in sulfide (mHS− = 0.0001−0.1) and chloride (mCl− = 0.1−5) solutions and the joint dissolution of Sb(s)0 and Sb2S3(s) in sulfide-chloride solution (mHS− = 0.01; mCl− = 1) depending on Eh, pH, and temperature. All thermodynamic calculations were carried out using the Chiller computer program. Under the above conditions, stibnite precipitates in acid, weakly acid to neutral, and medium redox solutions, whereas native antimony precipitates before stibnite under more reducing conditions in neutral to alkaline solutions.
The metal-bearing capacity of hydrothermal solutions (200–250 °C) of different compositions and origins has been predicted. We have established that the highest capacity is specific for acid (pH = 2–3) high-chloride solutions poor in sulfide sulfur and alkaline (pH = 7–8) low-chloride low-sulfide solutions.
The physicochemical modeling of mineral formation processes at the Badran subthrust gold-quartz deposit was performed, based on a study of fluid inclusions in quartz by Raman spectroscopy, gas chromatography, thermometry, and freezing. The results show that at stage I, highly productive gold-bearing quartz veins (gray quartz) of the deposit formed from heterogeneous fluid at <320 ºC and 2.0–0.1 kbar with the active participation of CO2, N2, and CH4; the salinity of this solution reached 10 wt.% NaCl-equiv. At stage II (Au-productive), milky-white quartz was produced from the homogeneous medium-chloride-sulfide solution which remained after the heterogenization of the initial fluid, at 300–100 ºC and 0.1 kbar. At stage III (with low Au production), clear quartz formed from homogeneous chloride solutions with salinity of <4.5 wt.% NaCl-equiv. at <200 ºC and <0.1 kbar. The physicochemical conditions of Au concentration within the complex geochemical system Au–Fe–Cu–Pb–Zn–As–Sb–Hg–Ag–H2O–Cl–H2S–CO2 at the Badran deposit was modeled using the Chiller software. The following models were used: (1) solution–rock interaction and (2) condensation of gas phase (for stage I); (3) simple cooling of medium-chloride-sulfide solution (for stage II); (4) simple cooling and (5) mixing of low-chloride-sulfide solution with acid meteoric waters (for stage III). The models show the sequence of vein formation in the ore-producing system and the host-rock metasomatism in the deep horizons of the deposit.
Представлены результаты экспериментальных измерений остаточных напряжений в элементах рельса, измеренных электромагнитно-акустическим структуроскопом СЭМА с использованием метода акустоупругости. Оценка внутренних напряжений произведена также в отдельных элементах рельса. Настройка чувствительности структуроскопа СЭМА и определение коэффициента акустоупругой связи выполнены в лабораторных условиях путем создания в отрезке рельса напряженного состояния одноосного сжатия в направлении продольной оси на испытательной машине Instron 300DX. Отмечена высокая чувствительность и достоверность измерений с погрешностью определения механических напряжений до 2 МПа и соответствие зарегистрированных структуроскопом механических напряжений нагрузке рельса, реализуемой на стенде. Остаточные напряжения, определяемые акустоупругим методом по измеряемой разнице времени пробега двух ортогонально поляризованных сдвиговых волн на участке от головки до подошвы и обратно, являются усредненными по сечению рельса и несут информацию о величине продольных напряжений в рельсе. Диапазон разброса измеренных в лаборатории остаточных напряжений в отрезках рельсов составил 49…67 МПа. С ростом сжимающей нагрузки происходит уменьшение скорости головной волны на всех измеряемых участках рельса. Для относительной оценки остаточных напряжений в отдельных элементах рельса выполнены измерения скорости распространения акустических волн по головке, шейке и подошве, показавшие, что остаточные напряжения в продольном направлении рельса, как правило, носят сжимающий характер для головки и растягивающий - для шейки.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.