Adobe is an ancient building technology made of sun dried bricks joined together by mud mortar. This paper deals with the physical and mechanical characterization of three different typologies of adobe bricks and one typology of mud mortar produced in Europe. They differed in terms of internal soil element proportions and amount of organic content. Physical tests consisted of granulometry, moisture content and density tests. The mechanical characterization consisted of uniaxial compressive tests and three point bending tests. Tests were performed according to modern material standards. The main mechanical properties both in tension and compression were determined at different curing conditions. The outcome provided in this study offers a general overview on the assessment of the mechanical performance of adobe in relation to the properties and interactions of its soil constituents. In fact, the comparison between components with the same soil mineralogical family and production process made it possible to assess both at a qualitative and quantitative level the effect of the physical properties of the mixture (such as fiber and clay percentages or moisture content) on the mechanical parameters of the resulting bricks and mortar. This paper proposes new predictive formulations of the most relevant material parameters in strength and deformation, such as compressive strength, deformation at peak stress and ultimate displacement for both adobe bricks and mortar. They quantify the influence that water content, clay percentage and fiber reinforcement produce on the mechanical performance of the tested adobe components. This was made possible by means of multivariate statistical analyses on the mechanical parameters derived from all the tested samples.

Adobe is one of the most ancient forms of masonry. Adobe bricks are sundried mixtures of clay, silt, sand and natural fibres locally available joined together using mud mortar. Adobe structures are largely spread in areas of the world prone to earthquakes or involved in military conflicts. Unfortunately, almost no literature concerns the dynamic assessment of soil-based masonry components. From earlier research, it was derived that the mechanical behaviour of adobe in statics fits in the class of quasi brittle materials. Its resemblance with cementitious materials concerns the main failure modes and the constitutive models in compression. This study deals with the experimental characterization of adobe components response in dynamics. It is aimed to study and quantify the rate sensitivity of adobe material from bricks at a wide range of strain rates, from statics up to impact conditions. In particular, the influence of fiber reinforcement in the mixture on the mechanical behaviour of the material has been addressed. Adobe bricks are commonly mixed using organic content locally available in the field, from straw to chopped wood. Fibres are added to prevent shrinkage cracks during the air drying process. In modern materials such as concrete, inclusion of artificial fibres is originally meant to enhance the mechanical performance of the material, benefiting from the selective properties of reinforcement and binder. An experimental campaign was carried out in a collaboration between Delft University of Technology, Dutch Ministry of Defence, TNO and the Joint Research Centre (JRC) of the European Commission. Two types of bricks were tested. They both had the same soil composition in terms of mineralogical family and soil elements proportions but only one was mixed using straw and wood. Cylindrical samples were subjected to compression tests at different rates of loadings in compression: low (˙ 1 = 3 10 −4 s −1), intermediate (˙ 2 = 3 s −1) and high (˙ 3 = 120 s −1). High strain rate tests were performed using the split Hopkinson bar of the Elsa-HopLab (JRC). For each test, high resolution videos registered the failure process and force-displacement plots were

No abstract

Abstract. In concrete often complex fracture and fragmentation patterns develop when subjected to high straining loads. The proper simulation of the dynamic cracking process in concrete is crucial for good predictions of the residual bearing capacity of structures in the risk of being exposed to extraordinary events like explosions, high velocity impacts or earthquakes.As it is well known, concrete is a highly rate dependent material. Experimental and numerical studies indicate that the evolution of damage is governed by complex phenomena taking place simultaneously at different material scales, i.e. micro, meso and macro-scales. Therefore, the constitutive law, and its rate dependency, must be adjusted to the level of representation. For a proper phenomenological (macroscopic) representation of the reality, the constitutive law has to explicitly describe all phenomena taking place at the lower material scales. Macro-scale inertia effects are implicitly simulated by the equation of motion.In the current paper, dynamic crack propagation and branching is studied with a new rate-dependent stress-based nonlocal damage model. The definition of rate in the constitutive law is changed to account for the inherent meso-scale structural inertia effects. This is accomplished by a new concept of effective rate which governs the dynamic delayed response of the material to variations of the deformation (strain) rate, usually described as micro-inertia effects. The proposed model realistically simulates dynamic crack propagation and crack branching phenomena in concrete.

No abstract

No abstract