Polymers with tailored architectures and degradability were prepared through thiocarbonyl addition ring-opening (TARO) atom-transfer radical polymerization (ATRP) using dibenzo[c,e]oxepin-5(7H)-thione (DOT), Cu(I)Br, and tris[2-(dimethylamino)ethyl]amine (Me 6 TREN) as the thionolactone, catalyst, and ligand, respectively, in combination with a selection of acrylic comonomers. Although copolymers with selectively degradable backbone thioesters and low dispersities (1.10 ≤ D̵ ≤ 1.26) were achieved using DMSO, acetonitrile, or toluene as the solvent, the Cu(I)-catalyzed dethionation of DOT to its (oxo)lactone analogue limited the achievable copolymer DOT content. Using anhydrous polymerization conditions minimized the side reaction and provided degradable copolymers with a higher (≤32 mol %) thioester content. Water-soluble molecular brushes were prepared by grafting poly(ethylene glycol) methyl ether acrylate−DOT copolymers from a pre-made multi-ATRP initiator. Due to copolymerization kinetics, the thioesters were installed close to the junctions and enabled the fast (<1 min) cleavage of the arms from the core to give water-soluble products using 10 mM oxone.

Pressure‐sensitive adhesives (PSAs) are made from soft, irreversibly lightly crosslinked polymers. Even after removal from surfaces, they retain insoluble networks which pose problems during the recycling of glass and cardboard. Herein, degradable PSAs are presented that provide the required performance in use but have networks that can be degraded after use. A series of copolymers was prepared through radical copolymerization of n‐butyl acrylate, 4‐acryloyloxy benzophenone (ABP) photo‐crosslinker, and dibenzo[c,e]oxepin‐5(7H)‐thione (DOT) to provide degradable backbone thioesters. The optimum tack and peel strengths were found for molar contents of 0.05 mol% ABP and 0.25 mol% DOT. Degradation of the backbone thioesters through aminolysis or thiolysis led to the full dissolution of the networks, loss of adhesive properties of films (decreases in the measured tack and peel strengths), and the quick detachment of model labels from a substrate. Inclusion of DOT into PSAs offers a viable route toward degradable and recyclable packaging labels.

The radical thiocarbonyl addition–ring-opening (TARO) copolymerization of thionolactones with vinyl comonomers affords selectively degradable thioester functional polymers promising for biomedical applications. Herein, the use of atom transfer radical polymerization (ATRP) is investigated for the first time, using dibenzo[c,e]oxepane-5(7H)-thione (DOT), Cu(I)Br, and tris[2-(dimethylamino)ethyl]amine (Me6TREN) as thionolactone, catalyst, and ligand, respectively, with the acrylate comonomers poly(ethylene glycol) methyl ether acrylate (PEGA), methyl acrylate, benzyl acrylate, and butyl acrylate. Polymerizations were impeded by a side reaction, the Cu(I)-catalyzed dethionation of DOT to its (oxo)lactone analog, which caused the loss of up to 50 mol% of DOT in the early polymerization stages and limited the final copolymer DOT content. Nonetheless, readily degradable copolymers with low dispersities (1.10 ≤ Ð ≤ 1.26) were formed using DMSO, acetonitrile, or toluene as solvent. Presuming adventitious water to be the oxygen source, the dethionation side reaction could be minimized (≥ 5 mol-% lactone) by using anhydrous polymerization conditions, which enabled the synthesis of copolymers with higher DOT content. Exploiting documented advantages of ATRP over thermally-initiated RAFT polymerization in the synthesis of brushes, water-soluble molecular brushes were prepared by grafting PEGA–DOT copolymers from a pre-made multi-ATRP initiator. Due to faster incorporation of DOT, the cleavable thioesters were located close to the junctions and enabled the fast (< 1 min) oxidative cleavage of the arms from the core to give water-soluble products using 10 mM oxone. Expanding the scope of the ATRP and TARO methods, this work presents facile access to polymer materials with tailored architectures and degradability.

Pressure‐sensitive adhesives (PSAs) are made from soft, irreversibly lightly crosslinked polymers. Even after removal from surfaces, they retain insoluble networks which pose problems during the recycling of glass and cardboard. Herein, degradable PSAs are presented that provide the required performance in use but have networks that can be degraded after use. A series of copolymers was prepared through radical copolymerization of n‐butyl acrylate, 4‐acryloyloxy benzophenone (ABP) photo‐crosslinker, and dibenzo[c,e]oxepin‐5(7H)‐thione (DOT) to provide degradable backbone thioesters. The optimum tack and peel strengths were found for molar contents of 0.05 mol% ABP and 0.25 mol% DOT. Degradation of the backbone thioesters through aminolysis or thiolysis led to the full dissolution of the networks, loss of adhesive properties of films (decreases in the measured tack and peel strengths), and the quick detachment of model labels from a substrate. Inclusion of DOT into PSAs offers a viable route toward degradable and recyclable packaging labels.