The uncontrollable non-planar electrodeposition of lithium is a significant barrier to the widespread adoption of high energy density rechargeable batteries with a lithium metal anode. A promising approach for preventing the growth of lithium dendrites is the use of solid polymer electrolytes with a high shear modulus. Current density is the key variable in the electrodeposition of lithium. The present study is the first attempt at quantifying the effect of current density on the geometry and density of dendrites and other protrusions during electrodeposition through a solid polymer electrolyte. The geometry and density of defects formed on the lithium electrode were determined by X-ray microtomography. The tomograms revealed protrusions on the electrodeposited lithium electrodes that were either globular or dendritic, or void defects. The range of current densities over which stable, planar deposition was observed is quantified. At higher current densities, globular protrusions were observed. At the highest current density, both globular and dendritic protrusions were observed. The areal density of protrusion defects increased sharply with current density, while the overall defect density is a weak function of current density. Our work enables comparisons between the experimentally determined onset of non-planar electrodeposition and prevailing theoretical predictions with no adjustable parameters.

Single-ion-conducting block copolymers are of considerable interest as electrolytes for battery systems, as they eliminate overpotentials due to concentration gradients. In this study, we characterize a library of poly(ethylene oxide) (PEO)-based diblock copolymers where the second block is poly(styrene-4-sulfonyltrifluoromethylsulfonyl)imide with either cation: univalent lithium or divalent magnesium counterions (PEO−PSLiTFSI or PEO−P[(STFSI) 2 Mg]). The PEO chain length is held fixed in this study. Polymers were synthesized in matched pairs that were identical in all aspects except for the identity of the counterion. Using rheology, SAXS, DSC, and AC impedance spectroscopy, we show that the dependence of morphology, modulus, and conductivity on composition in these charged copolymer systems is fundamentally different from uncharged block copolymers. At a given frequency and temperature, the shear moduli of the magnesiated copolymer systems were approximately 3−4 orders of magnitude higher than those of the matched lithiated pair. The shear moduli of all of the lithiated copolymers showed liquid-like rheological features while the magnesiated copolymers did not. All of the lithiated copolymers were completely disordered (homogeneous), consistent with the observed rheological properties. As expected, the moduli of the lithiated copolymers increased with increasing volume fraction of the ion-containing block (ϕ PSTFSI ), and the conductivity decreased with ϕ PSTFSI . However, the magnesiated copolymers followed a distinct trend. We show that this was due to the presence of microphase separation in the regime 0.21 ≤ ϕ PSTFSI ≤ 0.36, and the tendency for microphase separation became weaker with increasing ϕ PSTFSI . The magnesiated copolymer with ϕ PSTFSI = 0.38 was homogeneous. The morphological, rheological, and conductivity properties of these systems are governed by the affinity of the cations for PEO chains; homogeneous systems are obtained when the cations migrate from the ion-containing block to PEO.

Lithium metal is a high-energy-density battery electrode material, but the largely irreversible growth of lithium protrusions on an initially planar electrode during cycling makes it unsuitable for incorporation into a commercial battery. In this study, a lithium electrode with globular protrusions was stripped electrochemically, and the local morphology of the electrode as a function of time was determined by hard X-ray tomography. We demonstrate that globules are preferentially stripped compared to a planar electrode in our system, which incorporates a nanostructured block copolymer electrolyte. We report current density at the electrode as a function of micron-scale position and time. The local current density during the electrode healing process calculated from a reference frame at the electrode/electrolyte interface provides insight into the driving forces responsible for selective stripping of the globule. These results imply the possibility of discharging protocols that may return a lithium electrode to its initial planar state.

Plating and stripping of lithium protrusions in lithium metal symmetric cells containing a solid block copolymer electrolyte was studied as a function of time in 3D using time-resolved X-ray tomography. These measurements enabled determination of the spatial variation in current densities at the plating and stripping electrodes. The initial interelectrode distance was 27 μm. Correlation functions were calculated to reveal the relationships between current densities at the two electrodes and local electrolyte thickness. Current densities at opposing electrode locations during protrusion growth is uncorrelated until the local interelectrode distance decreases to less than 6 μm, just before the cell shorts. Mass balance was used to determine the area from which lithium ions that form a protrusion were stripped. Computational modeling of the plating and stripping process reveals the interplay between electrochemical and mechanical driving forces and their effect on nonuniform current distribution. Model predictions were compared with experiments without resorting to any adjustable parameters. The computed correlation functions were in qualitative agreement with experiments. Finally, the model was used to calculate contour plots of electrochemical potential within the electrolyte, shedding light on how geometry, salt concentration, interelectrode distance, and mechanical stress influence local rates of electrochemical reaction.