Abstract:The current paper studies the influence of geometrical parameters of the fused deposition modeling (FDM)-fused filament fabrication (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose-i.e., polylactic acid (PLA). The study was conducted using a set of different nozzles (0.4, 0.6, and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. Mesostructure evaluation through scanning electronic microscopy (SEM) scans of the samples was used to explain the obtained results. We detected a significant influence of geometric process parameters on sample mesostructure, and consequently, on sample strength.

Purpose This paper aims to investigate how the user-controlled parameters of the fused filament fabrication three-dimensional printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the polylactic acid part. Design/methodology/approach Fracture load in a three-point bending test and calculated related stress were used as a measure. The samples were printed with the long side along the z-axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. Temperature distribution on the sample surface during printing was monitored with a thermal imager. Sample mesostructure was analyzed using scanning electron microscopy. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. Findings It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength. Originality/value The novelty of the study consists in the generalization of the outcomes. All the parameters varied can be expressed through two factors, namely, the temperature of the previous layer and the extrusion efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads).

The ability to form closed cavities inside the part printed is an important feature of Fused Filament Fabrication technology. A typical part consists of a dense shell bearing the primary load, filled with low-density plastic scaffold (infill). Such a constitution of the part provides in most cases appropriate strength and low weight. However, if the printed part shape includes horizontal (orthogonal to printer’s Z axis) flat surfaces other than its top and bottom surface, then the shell of the part becomes interrupted, which may lead to drastic drop in the ability of the part to withstand loads. In the current study, a representative sample of a part with interrupted shell and testing apparatus is developed. Influence of shell and base thicknesses, as well as influence of the infill density on the part strength, are studied. Different approaches to the sample shape modification were applied and tested. The part shape optimization made with respect to peculiarities of Fused Filament Fabrication technology resulted in increment of the force, required to fracture the part from 483 to 1096 N and in decreased part mass from 36.9 to 30.2 g.

Current work investigates how user-controlled parameters of 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process temperature distribution on the samples surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.