Two novel double hydrophilic multiblock copolymers of N,N-dimethylacrylamide and N-isopropylacrylamide, m-PDMAp-PNIPAMq, with varying degrees of polymerization (DPs) for PDMA and PNIPAM sequences (p and q) were synthesized via consecutive reversible addition-fragmentation chain transfer (RAFT) polymerizations using polytrithiocarbonate (1) as the chain transfer agent (Scheme 1), where PDMA is poly(N,N-dimethylacrylamide) and PNIPAM is poly(N-isopropylacrylamide). The DPs of PDMA and PNIPAM sequences were determined by 1H NMR, and the block numbers, i.e., number of PDMAp-PNIPAMq sequences (n), were obtained by comparing the molecular weights of multiblock copolymers to that of cleaved products as determined by gel permeation chromatography (GPC). m-PDMA42-PNIPAM37 and m-PDMA105-PNIPAM106 multiblock copolymers possess number-average molecular weights (Mn) of 4.62x10(4) and 9.53x10(4), respectively, and the polydispersities (Mw/Mn) are typically around 1.5. Block numbers of the obtained multiblock copolymers are ca. 4, which are considerably lower than the numbers of trithiocarbonate moieties per chain of 1 (approximately 20) and m-PDMAp precursors (approximately 6-7). PDMA homopolymer is water soluble to 100 degrees C, while PNIPAM has been well known to exhibit a lower critical solution temperature (LCST) at ca. 32 degrees C. In aqueous solution, m-PDMA42-PNIPAM37 and m-PDMA105-PNIPAM106 multiblock copolymers molecularly dissolve at room temperature, and their thermo-induced collapse and aggregation properties were characterized in detail by a combination of optical transmittance, fluorescence probe measurements, laser light scattering (LLS), and micro-differential scanning calorimetry (micro-DSC). It was found that chain lengths of PDMA and PNIPAM sequences exert dramatic effects on their aggregation behavior. m-PDMA105-PNIPAM106 multiblock copolymer behaves as protein-like polymers and exhibits intramolecular collapse upon heating, forming unimolecular flower-like micelles above the thermal phase transition temperature. On the other hand, m-PDMA42-PNIPAM37 multiblock copolymer exhibits collapse and intermolecular aggregation, forming associated multimolecular micelles at elevated temperatures. The intriguing aggregation behavior of this novel type of double hydrophilic multiblock copolymers argues well for their potential applications in many fields such as biomaterials and biomedicines.

No abstract

An in situ microfluidic assembly approach is described that can both produce microsized building blocks and assemble them into complex multiparticle configurations in the same microfluidic device. The building blocks are microparticles of the biopolymer chitosan, which is intentionally selected because its chemistry allows for simultaneous intraparticle and interparticle linking. Monodisperse chitosan-bearing droplets are created by shearing off a chitosan solution at a microfluidic T-junction with a stream of hexadecane containing a nonionic detergent. These droplets are then interfacially crosslinked into stable microparticles by a downstream flow of glutaraldehyde (GA). The functional properties of these robust microparticles can be easily varied by introducing various payloads, such as magnetic nanoparticles and/or fluorescent dyes, into the chitosan solution. The on-chip connection of such individual particles into well-defined microchains is demonstrated using GA again as the chemical "glue" and microchannel confinement as the spatial template. Chain flexibility can be tuned by adjusting the crosslinking conditions: both rigid chains and semiflexible chains are created. Additionally, the arrangement of particles within a chain can also be controlled, for example, to generate chains with alternating fluorescent and nonfluorescent microparticles. Such microassembled chains could find applications as microfluidic mixers, delivery vehicles, microscale sensors, or miniature biomimetic robots.

A novel primary amine‐containing monomer, 1‐(3′‐aminopropyl)‐4‐acrylamido‐1,2,3‐triazole hydrochloride (APAT), was prepared from N‐propargylacrylamide and 3‐azidopropylamine hydrochloride via copper‐catalyzed Huisgen 1,3‐dipolar cycloaddition (click reaction). Poly(N‐isopropylacrylamide)‐b‐poly(1‐(3′‐aminopropyl)‐4‐acrylamido‐1,2,3‐triazole hydrochloride), PNIPAM‐b‐PAPAT, was then synthesized via consecutive reversible addition‐fragmentation chain transfer polymerizations of N‐isopropylacrylamide and APAT. In aqueous solution, the obtained thermoresponsive double hydrophilic block copolymer dissolves molecularly at room temperature and self‐assembles into micelles with PNIPAM cores and PAPAT shells at elevated temperature. Because of the presence of highly reactive primary amine moieties in PAPAT block, two types of covalently stabilized nanoparticles namely core crosslinked and shell crosslinked micelles with ‘inverted’ core‐shell nanostructures were facilely prepared upon the addition of glutaric dialdehyde at 25 and 50 °C, respectively. In addition, the obtained structure‐fixed micelles were incorporated with gold nanoparticles via in situ reduction of preferentially loaded HAuCl4. High resolution transmission electron microscopy revealed that gold nanoparticles can be selectively loaded into the crosslinked cores or shells, depending on the micelle templates employed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6518–6531, 2008

No abstract

No abstract

No abstract

No abstract