Structural control technologies have attracted great interest from the earthquake engineering community over the last few decades as an effective method of reducing undesired structural responses. Traditional structural control systems employ large quantities of cables to connect structural sensors, actuators, and controllers into one integrated system. To reduce the high-costs associated with labor-intensive installations, wireless communication can serve as an alternative real-time communication link between the nodes of a control system. A prototype wireless structural sensing and control system has been physically implemented and its performance verified in large-scale shake table tests. This paper introduces the design of this prototype system and investigates the feasibility of employing decentralized and partially decentralized control strategies to mitigate the challenge of communication latencies associated with wireless sensor networks. Closed-loop feedback control algorithms are embedded within the wireless sensor prototypes allowing them to serve as controllers in the control system. To validate the embedment of control algorithms, a 3-story half-scale steel structure is employed with magnetorheological (MR) dampers installed on each floor. Both numerical simulation and experimental results show that decentralized control solutions can be very effective in attaining the optimal performance of the wireless control system.
Wireless sensor networks have rapidly matured in recent years to offer data acquisition capabilities on par with those of traditional tethered data acquisition systems. Entire structural monitoring systems assembled from wireless sensors have proven to be low cost, easy to install, and accurate. However, the functionality of wireless sensors can be further extended to include actuation capabilities. Wireless sensors capable of actuating a structure could serve as building blocks of future generations of structural control systems. In this study, a wireless sensor prototype capable of data acquisition, computational analysis and actuation is proposed for use in a real‐time structural control system. The performance of a wireless control system is illustrated using a full‐scale structure controlled by a semi‐active magnetorheological (MR) damper and a network of wireless sensors. One wireless sensor designated as a controller automates the task of collecting state data, calculating control forces, and issuing commands to the MR damper, all in real time. Additional wireless sensors are installed to measure the acceleration and velocity response of each system degree of freedom. Base motion is applied to the structure to simulate seismic excitations while the wireless control system mitigates inter‐storey drift response of the structure. An optimal linear quadratic regulation solution is formulated for embedment within the computational cores of the wireless sensors. Copyright © 2007 John Wiley & Sons, Ltd.
The performance aspects of a wireless "active" sensor, including the reliability of the wireless communication channel for real-time data delivery and its application to feedback structural control, are explored in this study. First, the control of magnetorheological (MR) dampers using wireless sensors is examined. Second, the application of the MR-damper to actively control a half-scale three-story steel building excited at its base by shaking table is studied using a wireless control system assembled from wireless active sensors. With an MR damper installed on each floor (3 dampers total), structural responses during seismic excitation are measured by the system's wireless active sensors and wirelessly communicated to each other; upon receipt of response data, the wireless sensor interfaced to each MR damper calculates a desired control action using an LQG controller implemented in the wireless sensor's computational core. In this system, the wireless active sensor is responsible for the reception of response data, determination of optimal control forces, and the issuing of command signals to the MR damper. Various control solutions are formulated in this study and embedded in the wireless control system including centralized and decentralized control algorithms.
The behavior of story-isolated structures during an earthquake is highly affected by the characteristics of the isolation system and its location along the height of the building. Interaction between the super-structure and the sub-structure with mid-story isolation as nonlinear connector makes the mid-story isolation building even more complicated during the earthquake excitation. In this paper, two different identification techniques are applied to identify the time-varying dynamic characteristics of the mid-story isolation building using the ambient vibration test data as well as the earthquake response data. For the ambient vibration measurements, the recursive stochastic subspace identification method is used, whereas for the earthquake response data the recursive subspace identification is used. Comparison on dynamic characteristics of the story-isolated building from the results of identification is made, and the effect of nonlinear behavior of the mid-isolation system to the response of the building during the earthquake is discussed.
In recent years, substantial research has been conducted to advance structural control as a direct means of mitigating the dynamic response of civil structures. In parallel to these efforts, the structural engineering field is currently exploring low-cost wireless sensors for use in structural monitoring systems. To reduce the labor and costs associated with installing extensive lengths of coaxial wires in today's structural control systems, wireless sensors are being considered as building blocks of future systems. In the proposed system, wireless sensors are designed to perform three major tasks in the control system; wireless sensors are responsible for the collection of structural response data, calculation of control forces, and issuing commands to actuators. In this study, a wireless sensor is designed to fulfill these tasks explicitly. However, the demands of the control system, namely the need to respond in real-time, push the limits of current wireless sensor technology. The wireless channel can introduce delay in the communication of data between wireless sensors; in some rare instances, outright data loss can be experienced. Such issues are considered an intricate part of this feasibility study. A prototype Wireless Structural Sensing and Control (WiSSCon) system is presented herein. To validate the performance of this prototype system, shaking table experiments are carried out on a half-scale three story steel structure in which a magnetorheological (MR) damper is installed for real-time control. In comparison to a cable-based control system installed in the same structure, the performance of the WiSSCon system is shown to be effective and reliable.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.