No abstract

No abstract

In this paper, a fuzzy expert off-line system has been developed for fault diagnosis in the distribution network based on the structural and functional operation of the relay and circuit breakers. Functional operations (correct operation, false operation and failure to operate) of the relays and circuit breakers are described by fuzzy logic. Input data for the proposed fuzzy expert fault diagnosis system (FDS) are status and time stamps of the alarms, associated with relays and circuit breakers. The diagnostic system from a huge number of alarms sets, logically organizes and quantifies the diagnosis. FDS can diagnose correct operation, false operation and failure to operate of the relays and circuit breakers. Also, it can identify and quantify fault location based on the Hamacher’s operator of a fuzzy union. The additional contribution of this paper is in modeling unknown information using linear fuzzy membership function. Statuses of certain components may be unknown due to telemetry failures or are simply unavailable to the operator and proposed FDS can make diagnosis in such a situation. Developed fuzzy expert FDS is tested on the two examples of faults in real life distribution network

Original scientific paper Recently, there has been made a great effort to include electricity generation from the renewable energy sources into the power system. Random renewable generation creates the imbalance between electricity production and consumption, which requires power plants with fast response or energy storage systems. Generally accepted solution for load balancing is the concept of smart grids and one of the elements of smart grid efficiency is the ability of real-time demand-supply balancing. In this paper, the model of the part of power distribution network of the city of Osijek has been created based on results of the power measurements of total electricity consumption in a family house in Osijek, air conditioning system consumption and PV power plant production. Also, algorithm for real-time load management is proposed. It assumes coordinated control of air conditioning system units depending on the production of PV power plants and electricity consumption of distribution network, in order to reduce peak demand in the distribution network.Keywords: demand side load management; distribution system; photovoltaic generation; real-time demand-supply balancing; smart grid Upravljanje potražnjom u distribucijskom sustavu s fotonaponskim elektranamaIzvorni znanstveni članak Posljednjih godina učinjen je znatan napor na uključivanju obnovljivih izvora električne energije u elektroenergetski sustav. Nepredvidiva prozvodnja obnovljivih izvora električne energije stvara neravnotežu između proizvodnje i potrošnje, što onda zahtijeva elektrane s brzim odzivom, ili sustave skladištenja električne energije. Opće prihvaćeno rješenje za uravnoteženje potrošnje je koncept naprednih mreža, a jedan od elemenata učinkovitosti naprednih mreža je sposobnost za uravnoteženje potražnje i opskrbe u stvarnom vremenu. U ovom radu razvijen je model dijela distribucijske mreže grada Osijeka i to na temelju rezultata mjerenja ukupne potrošnje obiteljske kuće u Osijeku, potrošnje klimatizacijskog uređaja te proizvodnje fotonaponske elektrane. Također, predložen je algoritam za upravljanje potražnjom u stvarnom vremenu. Algoritam sadrži usklađeno upravljanje klimatizacijskim uređajima ovisno o proizvodnji fotonaponskih elektrana te o potrošnji u distribucijskoj mreži, a u cilju snižavanja vršne potražnje u distribucijskoj mreži.Ključne riječi: distribucijski sustav; napredne mreže; proizvodnja fotonaponske elektrane; upravljanje potražnjom; uravnoteženje potražnje i opskrbe u stvarnom vremenu

Voltage dips represent a significant power quality problem. The main cause of voltage dips and short-term interruptions is an electrical short circuit that occurs in transmission or distribution networks. Faults in the power system are stochastic by nature and the main cause of voltage dips. As faults in the transmission system can affect more customers than faults in the distribution system, to reduce the number of dips, it is not enough to invest in a small part of the transmission or distribution system. Only targeted investment in the whole (or a large part of the) power system will reduce voltage dips. Therefore, monitoring parts of the power system is very important. The ideal solution would be to cover the entire system so that a power quality (PQ) monitor is installed on each bus, but this method is not economically justified. This paper presents an advanced method for determining the optimal location and the optimal number of voltage dip measuring devices. The proposed algorithm uses a monitor reach area matrix created by short-circuit simulations, and the coefficient of the exposed area. Single-phase and three-phase short circuits are simulated in DIgSILENT software on the IEEE 39 bus test system, using international standard IEC 60909. After determining the monitor reach area matrix of all potential monitor positions, the binary bat algorithm with a coefficient of the exposed area of the system bus is used to minimize the proposed objective function, i.e., to determine the optimal location and number of measuring devices. Performance of the binary bat algorithm is compared to the mixed-integer linear programming algorithm solved by using the GNU Linear Programming Kit (GLPK).

Due to construction of a highway in the eastern part of Croatia, a new 110/x kV substation was built with two parallel connecting underground cables. Cables were connected to already existing 110 kV overhead lines. At the place where the transition between overhead lines and cables is made, surge arresters were installed. In this paper lightning stroke at the grounding wire on the overhead line and its impact on underground cables were studied. Transient program Electromagnetic Transients Program (ATP-EMTP) is used to create a model of the system and to perform simulation of the transient process during lightning stroke. The results of the simulation are briefly presented and discussed in the paper.

Abstract:The integration of distributed energy sources transforms passive distributed grid, in which the energy flows only in one direction (from the source to the consumer), in an active one, in which energy flows in both directions. To maximize positive impacts, which distributed generation (DG) can provide to the distribution network, it is necessary to determine the optimal allocation of distributed generation. The optimal allocation can be determined by using the optimization method. There are two main categories: exact methods (traditional) and heuristic (non-traditional) methods. Exact methods search for global optimum while heuristic methods achieve satisfactory solutions with greater computation speed. This paper gives a brief review of non-traditional methods used for determining optimal location and optimal power of DG with the aim to reduce real power losses and to improve voltage characteristics. Also, there is a review of the application of those methods in determining the optimal power, optimal location and optimal cycle of charging/discharging of electrical energy storage systems.

Stochastic production from wind power plants imposes additional uncertainty in power system operation. It can cause problems in load and generation balancing in the power system and can also cause congestion in the transmission network. This paper deals with the problems of congestion in the transmission network, which are caused by the production of wind power plants. An optimization model for corrective congestion management is developed. Congestions are relieved by re-dispatching several cascaded hydropower plants. Optimization methodology covers the optimization period of one day divided into the 24 segments for each hour. The developed optimization methodology consists of two optimization stages. The objective of the first optimization stage is to obtain an optimal day-ahead dispatch plan of the hydropower plants that maximizes profit from selling energy to the day-ahead electricity market. If such a dispatch plan, together with the wind power plant production, causes congestion in the transmission network, the second optimization stage is started. The objective of the second optimization stage is the minimization of the re-dispatching of cascaded hydropower plants in order to avoid possible congestion. The concept of chance-constrained programming is used in order to consider uncertain wind power production. The first optimization stage is defined as a mixed-integer linear programming problem and the second optimization stage is defined as a quadratic programming (QP) problem, in combination with chance-constrained programming. The developed optimization model is tested and verified using the model of a real-life power system.