No abstract

Continuous exposure in the Pindos mountain chain (Greece) and the detailed stratigraphic measurements in the area enable us to construct eight balanced cross sections across the Pindos Fold-and-thrust belt (PFTB) and to approach quantitatively some parameters which controlled foreland evolution. The 160-km-wide passive continental margin of the Apulian continent in Greece was progressively shortened from east to west at rates of 6 mm/year between the Early Oligocene and Late Eocene. From the rear to the frontal part of the wedge, fault-bend folds, duplexes and imbricates were formed, while strain was partitioned into faulting (~34%), layer parallel shortening (~23%) and buckling (~9%). Foreland subsidence and internal deformation of the orogenic wedge are strongly affected by two parameters of equal importance: the thrust load of the overthrusted microcontinents and the rigidity of the underthrusted Apulian passive margin. Changes in the thickness of the pre-orogenic sediments and reactivated transform faults induced salients. During the Lower Miocene, the orogenic wedge in the Peloponnese suffered additional uplift and westward gravitational gliding induced by the intracontinental subduction of the Palaeozoic rift zone of the Phyllite-Quartzite Series, which was reactivated and returned to the earth's surface during the Hellenic orogeny.

An exhumation model comprising forward and backward thrusting and late orogenic collapse is proposed in order to explain the kinematics of the tectonic windows in the south Peloponnesus. The model is based on mapping, mesoscopic structural data and strain analysis. Syn-compressional thickening took place throughout the Oligocene and Early Miocene which includes the subduction of the Pindos Ocean at the western margin of the Pelagonian microcontinent and the intracontinental subduction of the Phyllite± Quartzite and the Plattenkalk series. The latter subduction was associated with blueschist metamorphism, westward-directed ductile thrusting, and folding. The exhumation history of the deeper parts of the orogen began at the Oligocene±Miocene boundary with the progressive entrance of the low-density crust and the Plattenkalk carbonates in the subduction zone. Increased buoyancy caused: (a) the initiation of the Phyllite±Quartzite series extrusion; (b) vertical coaxial stretching; and (c) the evolution of two pop-up structures, i.e. the Parnon and Taygetos anticlines. This syn-compressional exhumation was taking place in the lower Miocene with decreasing rates from 7 to 1.5 mm/year. The change in the local stress field from compression to extension began in the middle Miocene with the formation of hinterland-dipping normal faults. The exhumation/denudation rate caused by the footwall uplift along these faults does not exceed 0.2 mm/year.

The mineralogical composition, microfabrics and geochemistry of a set of eight samples derived from a narrow area of NE Peloponnese (Greece), where engineering works are presently in progress, were investigated in this study. No important mineralogical differences were observed between the samples other than a variation in the proportions of the participating phases. Analyses reveal that these sediments consist mainly of carbonates (calcite, dolomite), quartz and feldspars (albite, orthoclase). Carbonate minerals exhibit a micritic texture and a high degree of cementation bonding. Phyllosilicates and clay minerals are also common, with smectite and mixed-layer smectite-chlorite being the prevailing phases, followed by chlorite and white mica (muscovite, illite). According to the physical properties measured on bulk samples, the samples were found to exhibit a low to medium expansion, low to intermediate plasticity, normal activity and brittle behaviour. The porosity does not exceed 46% and the organic matter ranges between 3.80 and 5.00%. The high degree of cementation, the dispersed appearance of clays, the small pores (<10 μm) and the common occurrence of smectite in a mixed-layer with chlorite are all favourable characteristics, positively influencing the sediment's stability for engineering constructions.