Alat Penukar Kalor (APK) tipe kompak yang memiliki unjuk kerja yang optimal, yaitu perpindahan kalor yang maksimal dan penurunan tekanan yang minimal dengan volume konstruksi APK yang kecil dan ringan dengan memvariasikan diameter lubang pembangkit vorteks winglet melengkung berlubang terhadap unjuk kerja apk tipe kompak melalui studi eksperimental sehingga diperoleh penyerapan kalor yang maksimal dan efektifitas APK tipe kompak yang ditunjukan oleh koefisien perpindahan kalor dan mendapatkan penurunan tekanan total dan koefisein gesek yang terkait dengan desain pembangkit vorteks winglet melengkung berlubang. Model uji terdiri dari 12 pelat aluminium paralel dengan ukuran 300 mm x 300 dan 12 mm jarak antar sirip . Percobaan dilakukan dengan sejumlah pasangan pembangkit vorteks yang memiliki variasi diameter. Eksperiment dilakukan di terowongan angin dimana APK dipanaskan oleh air panas aliran silang (cross-flow). Udara yang dialirkan oleh blower, melewati generator vortex terpasang di bagian sirip aluminium. Seluruh data pengujian akan direkam setiap 3 detik dengan Arduino PLX Data Acquisition yang dihubungkan ke Laptop. Dalam penelitian ini sudut serangan dijaga konstan,β = 45, Dengan variasi diameter lubang pada pembangkit vorteks. Dari hasil pengujian alat penukar kalor terlihat bahwasanya alat-alat yang dibuat berkerja sesuai dengan yang diharapkan Winglet dengan lubang memiliki pengaruh dalam membuat aliran udara menjadi bergolak sehingga meningkatkan penyerapan kalor oleh udara. Pada penelitian ini terlihat bahwa diameter winglet sebesar 6 mm memberikan pengaruh yang baik dalam peningkatan penyerapan kalor dan juga penurunan tekanan yang relatif lebih rendah Kata Kunci: APK tipe kompak, Arduino, plx daq, vorteks
Proses elektrolisis air sedang dikembangkan untuk menghasilkan hidrogen. Namun, karena proses elektrolisis membutuhkan energi listrik sebagai pemicu reaksi, proses ini memberikan efisiensi yang relatif rendah. Proses elektrolisis berfungsi jika ketersediaan sumber energi listrik mudah diperoleh dengan harga murah. Pengujian dengan variasi jarak katoda dan anoda, campuran elektrolit dan jenis elektroda yang digunakan terus dikembangkan untuk mengurangi jumlah energi listrik yang digunakan dalam proses elektrolisis sehingga dapat diterapkan dalam kehidupan sosial, tetapi belum belum menuai hasil yang memuaskan. Penelitian ini menggunakan sumber arus baterai 12V, dan jarak yang telah ditetapkan pada katoda dan anoda ialah 80 mm,120 mm dan 200 mm. Jenis elektroda yang digunakan Stainless steel, Aluminium dan Tembaga, dengan jumlah campuran garam yang terlarut ialah 250 gram dalam lima liter air, atau 50 gram perliter air. Hasil dari pengujian, tekanan gas yang dihasilkan oleh elektroda yang berbahan stainless steel lebih tinggi dibandingkan oleh elektroda yang berbahan aluminium dan tembaga dan semakin dekat jarak elektroda maka tekanan gas yang dihasilkan semakin tinggi. Dengan menggunakan manometer tabung U tekanan gas hidrogen tertinggi diukur pada elektroda stainless steel pada sisi katoda jarak 80 mm sebesar 9733 Pa. Sedangkan tekanan hydrogen pada elektroda aluminium pada sisi katoda 9246.8 Pa, dan tekanan hidrogen terendah diukur pada elektroda tembaga 6034 Pa. Hasil pengujian menunjukkan perbedaan tekanan dari setiap jenis elektroda.
The water turbine is a device that converts water flow energy into shaft mechanical energy. Before being converted into mechanical energy in the turbine, the potential energy needs to be converted into kinetic energy first. The vortex will move the turbine blades which cause the runner to rotate so that there is a change in the kinetic energy of the water into mechanical energy in the turbine which is used to drive the generator and then into electrical energy. The purpose of this research is to analyze the torque that occurs on the shaft and turbine power. Water is flowed to the test with a pump through a control valve. The water flow is read by a rotameter attached to the pipe to the upper reservoir, while the torque is measured using a load cell, while the rotation is measured using a photo sensor interrupt to read the movement of the counter wheel. Data from load cell and photo sensor interruptor is read using Arduino Uno then the data is stored on laptop in excel file using plx-daq software. The minimum torque for the 8 blades is 9,12 kg.mm and 7.61 kg.mm for 6 blades at a water flow rate of 90 l / min. The maximum torque occurs at the 8 blades of 10.06 kg.mm while the maximum torque at blade 6 is 9,12 kg.mm at the same water flow rate of 150 l / min. The minimum turbine power for the 8 blades is 0.47 W and 0.27 W for the 6 blades at a water flow rate of 90 l / min. The maximum turbine power at blade 8 is 1.03 W, while the maximum power at blade 6 is 0.91 W at the same water flow rate of 150 l / min. From the data analysis, it can be seen that the power for the turbine with the number of blades 8 tends to be greater than the power for the turbine with 6 blades, but if the percentage increases in power between the 8 blades and 6 blades the trend decreases even though the flow rate is increasing.
This paper presents the development of dynamometer to measure cutting force in turning operation in particular the tangential force (Ft). The dynamometer utilises a straight bar load cell that connected to holder tool to measure at least one axis of force. The designed dynamometer is capable of computing the forces acting on the workpiece in turning operation using any data acquisition system. Two materials of low elastic modulus, Polyoxymethylene (POM) and Polytetrafluoroethylene (PTFE), were employed as workpieces to test the performance of dynamometer. The performance of the dynamometer to measure one axis of cutting forces is considered satisfactory mainly because of the simplicity and low cost are the main requirements in design and construction.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.