Several experiments, related to controlled thermonuclear fusion research and highly relevant for large size tokamaks, including ITER, have been carried out in ADITYA, an ohmically heated circular limiter tokamak. Repeatable plasma discharges of a maximum plasma current of ~160 kA and discharge duration beyond ~250 ms with a plasma current flattop duration of ~140 ms have been obtained for the first time in ADITYA. The reproducibility of the discharge reproducibility has been improved considerably with lithium wall conditioning, and improved plasma discharges are obtained by precisely controlling the position of the plasma. In these discharges, chord-averaged electron density ~3.0–4.0 × 1019 m−3 using multiple hydrogen gas puffs, with a temperature of the order of ~500–700 eV, have been achieved. Novel experiments related to disruption control are carried out and disruptions, induced by hydrogen gas puffing, are successfully mitigated using the biased electrode and ion cyclotron resonance pulse techniques. Runaway electrons are successfully mitigated by applying a short local vertical field (LVF) pulse. A thorough disruption database has been generated by identifying the different categories of disruption. Detailed analysis of several hundred disrupted discharges showed that the current quench time is inversely proportional to the q edge. Apart from this, for volt–sec recovery during the plasma formation phase, low loop voltage start-up and current ramp-up experiments have been carried out using electron cyclotron resonance heating (ECRH). Successful recovery of volt–sec leads to the achievement of longer plasma discharge durations. In addition, the neon gas puff assisted radiative improved confinement mode has also been achieved in ADITYA. All of the above mentioned experiments will be discussed in this paper.
ITER magnetic diagnostics are now in their detailed design and R&D phase. They have passed their conceptual design reviews and a working diagnostic specification has been prepared aimed at the ITER project requirements. This paper highlights specific design progress, in particular, for the in-vessel coils, steady state sensors, saddle loops and divertor sensors. Key changes in the measurement specifications, and a working concept of software and electronics are also outlined.
ITER is an experimental nuclear reactor, aiming to demonstrate the feasibility of nuclear fusion realization in order to use it as a new source of energy. ITER is a plasma device (tokamak type) which will be equipped with a set of plasma diagnostic tools to satisfy three key requirements: machine protection, plasma control and physics studies by measuring about 100 different parameters. ITER diagnostic equipment is integrated in several ports at upper, equatorial and divertor levels as well internally in many vacuum vessel locations. The Diagnostic Systems will be procured from ITER Members (Japan, Russia, India, United States, Japan, Korea and European Union) mainly with the supporting structures in the ports. The various diagnostics will be challenged by high nuclear radiation and electromagnetic fields as well by severe environmental conditions (ultra high vacuum, high thermal loads). Several neutron systems with different sensitivities are foreseen to measure ITER expected neutron emission from 10 14 up to almost 10 21 n/s. The measurement of total neutron emissivity is performed by means of Neutron Flux Monitors (NFM) installed in diagnostic ports and by Divertor Neutron Flux Monitors (DNFM) plus MicroFission Chambers (MFC) located inside the vacuum vessel. The neutron emission profile is measured with radial and vertical neutron cameras. Spectroscopy is accomplished with spectrometers looking particularly at 2.5 and 14 MeV neutron energy. Neutron Activation System (NAS), with irradiation ends inside the vacuum vessel, provide neutron yield data. A calibration strategy of the neutron diagnostics has been developed foreseeing in situ and cross calibration campaigns. An overview of ITER neutron diagnostic systems and of the associated challenging engineering and integration issues will be reported.
Short bursts (∼1 ms) of gas, injecting ∼1017–1018 molecules of hydrogen and/or deuterium, lead to the observation of cold pulse propagation phenomenon in hydrogen plasmas of the ADITYA-U tokamak. After every injection, a sharp increase in the chord-averaged density is observed followed by an increase in the core electron temperature. Simultaneously, the electron density and temperature decrease at the edge. All these observations are characteristics of cold pulse propagation due to the pulsed gas application. The increase in the core temperature is observed to depend on the values of both the chord-averaged plasma density at the instant of gas-injection and the amount of gas injected below a threshold value. Increasing the amount of gas-puff leads to higher increments in the core-density and the core-temperature. Interestingly, the rates of rise of density and temperature remain the same. The gas-puff also leads to a fast decrease in the radially outward electric field together with a rapid increase in the loop-voltage suggesting a reduction in the ion-orbit loss and an increase in Ware-pinch. This may explain the sharp density rise, which remains mostly independent of the toroidal magnetic field and plasma current in the experiment. Application of a subsequent gas-puff before the effect of the previous gas-pulse dies down, leads to an increase in the overall electron density and consequently the energy confinement time.
Since the 2018 IAEA-FEC conference, in addition to expanding the parameter horizons of the ADITYA-U machine, emphasis has been given to dedicated experiments on inductively driven particle injection (IPI) for disruption studies, runaway electron (RE) dynamics and mitigation, plasma rotation reversal, radiative-improved modes using Ne and Ar injection, modulation of magneto–hydrodynamic modes, edge turbulence using periodic gas puffs and electrode biasing (E-B). Plasma parameters close to the design parameters of circular plasmas with H2 and D2 as fuel have been realized, and the shaped plasma operation has also been initiated. Consistent plasma discharges having I P ∼ 100–210 kA, t ∼ 300–400 ms, n e ∼ 3–6 × 1019 m−3, core T e ∼ 300–500 eV were achieved with a maximum B T of ∼1.5 T. The enhanced plasma parameters are the outcome of repeated cycles of baking (135 °C), followed by extensive wall conditioning, which includes pulsed glow discharge cleaning in H, He and Ar–H mixture, and lithiumization. A higher confinement time has been observed in D2 compared to H2 plasmas. Furthermore, shaped plasmas are attempted for the first time in ADITYA-U. A first of its kind inductively driven particle injection for disruption mitigation studies has been developed and operated. The injection of solid particles into the plasma core leads to a fast current quench. Two pulses of electron cyclotron resonance wave at 42 GHz are launched in a single discharge: one pulse is used for pre-ionization and the second for heating. In a novel approach, a positively biased electrode is used to confine REs after discharge termination. E-B is also used for controlling the rotation of drift-tearing modes by changing the plasma rotation. Cold pulse propagation and signatures of detachment are observed during the injection of short gas puffs. A correlation between the plasma toroidal rotation and the total radiated power has been observed with neon gas injection-induced improved confinement modes.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.