A large-area, fabric-like pump would potentially have applications, for example, in controlling water transport through a garment, such as a rain jacket, regardless of the external temperature and humidity. This paper presents an all-plastic, flexible electroosmotic pump, constructed from commercially available materials: A polycarbonate membrane combined with the electrochemically active polymer poly(3,4-ethylenedioxythiophene) polystyrene sulfonate that actively transports water using an electric potential that can be supplied by a small battery. By using electrochemically active polymer electrodes instead of metal electrodes, the electrochemical reaction that drives flow avoids the oxygen and hydrogen gas production or pH changes associated with water electrolysis. We observe a water mass flux up to 23 mg min −1 per cm 2 polycarbonate membrane (porosity 10-15%), at an applied potential of 5 V, and a limiting operating pressure of 0.3 kPa V −1 , similar to previously reported membrane-based electroosmotic pumps.

There is a need for soft actuators in various biomedical applications to manipulate delicate objects such as cells and tissues. Soft actuators are able to adapt to any shape and limit the stress applied to delicate objects. Conjugated polymer (CP) actuators, especially in the so-called trilayer configuration, are interesting candidates for driving such micromanipulators. However, challenges involved in patterning the electrodes in a trilayer with individual contact have prevented further development of soft micromanipulators based on CP actuators. To allow such patterning, two printing-based patterning techniques have been developed. First, an oxidant layer is printed using either syringe-based printing or microcontact printing, followed by vapor-phase polymerization of the CP. Submillimeter patterns with electronic conductivities of 800 S·cm are obtained. Next, laser ablation is used to cleanly cut the final device structures including the printed patterns, resulting in fingers with individually controllable digits and miniaturized hands. The methods presented in this paper will enable integration of patterned electrically active CP layers in many types of complex three-dimensional structures.

In nearly all cases, electrophoresis in gels is driven via the electrolysis of water at the electrodes, where the process consumes water and produces electrochemical by-products. We have previously demonstrated that π-conjugated polymers such as poly(3,4-ethylenedioxythiophene) (PEDOT) can be placed between traditional metal electrodes and an electrolyte to mitigate electrolysis in liquid (capillary electroosmosis/electrophoresis) systems. In this report, we extend our previous result to gel electrophoresis, and show that electrodes containing PEDOT can be used with a commercial polyacrylamide gel electrophoresis system with minimal impact to the resulting gel image or the ionic transport measured during a separation.

Recent advances in microfluidic devices put a high demand on small, robust and reliable pumps suitable for high-throughput applications. Here we demonstrate a compact, low-cost, directly attachable (clip-on) electroosmotic pump that couples with standard Luer connectors on a microfluidic device. The pump is easy to make and consists of a porous polycarbonate membrane and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) electrodes. The soft electrode and membrane materials make it possible to incorporate the pump into a standard syringe filter holder, which in turn can be attached to commercial chips. The pump is less than half the size of the microscope slide used for many commercial lab-on-a-chip devices, meaning that these pumps can be used to control fluid flow in individual reactors in highly parallelized chemistry and biology experiments. Flow rates at various electric current and device dimensions are reported. We demonstrate the feasibility and safety of the pump for biological experiments by exposing endothelial cells to oscillating shear stress (up to 5 dyn/cm 2 ) and by controlling the movement of both micro-and macroparticles, generating steady or oscillatory flow rates up to ± 400 μL/min.

Fabrication of miniaturized devices is usually time-consuming, costly, and the materials commonly used limit the structures that are possible to create. The techniques most often used to make microsystems involve multiple steps, where each step takes considerable time, and if only a few systems are to be made, the price per device becomes excessive. This thesis describes how a simple syringebased 3D-printer, in combination with an appropriate choice of materials, can reduce the delay between design and prototype and simplify fabrication of microsystems. This thesis suggest two types of materials that we propose be used in combination with 3D-printing to further develop microsystems for biology and biochemistry.Analytical applications in biology and biochemistry often contain electrodes, such as in gel electrophoresis. Faradaic (electrochemical) reactions have to occur at the metal electrodes to allow electron-to-ion transduction through an electrolyte-based system to drive a current when a potential is applied to the electrodes in an electrolyte-based system. These electrochemical reactions at the electrodes, such as water electrolysis, are usually problematic when miniaturizing devices and analytical systems. An alternative to metal electrodes can be electrochemicallyactive conducting polymers, e.g. poly(3,4-ethylenedioxythiophene) (PEDOT), which can be used to reduce electrolysis when driving a current through water-based systems. Paper 1 describes gel electrophoresis where the platinum electrodes were replaced with the conductive polymer PEDOT, without affecting the separation.Manufacturing and prototyping of microsystems can be simplified by using 3D-printing in combination with a sacrificial material. A sacrificial template material can further simplify bottom-up manufacturing of more complicated forms such as protruding and overhanging structures. We showed in paper 2 that polyethylene glycol (PEG), in combination with a carbonate-based plasticizer, functions well as a 3D-printable sacrificial template material. PEG2000 with between 20 wt% and 30 wt% ethylene carbonate or propylene carbonate has properties advantageous for 3D-printing, such as shear-thinning rheology, mechanical and chemical stability, and easy dissolution in water.  Familj och vänner utanför akademin som gör sitt bästa för att försöka förstå.