In this study, biochars derived from waste fiberboard biomass were applied in tetracycline (TC) removal in aqueous solution. Biochar samples were prepared by slow pyrolysis at 300, 500, and 800 • C, and were characterized by ultimate analysis, Fourier transform infrared (FTIR), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET), etc. The effects of ionic strength (0-1.0 mol/L of NaCl), initial TC concentration (2.5-60 ppm), biochar dosage (1.5-2.5 g/L), and initial pH (2-10) were systemically determined. The results present that biochar prepared at 800 • C (BC800) generally possesses the highest aromatization degree and surface area with abundant pyridinic N (N-6) and accordingly shows a better removal efficiency (68.6%) than the other two biochar samples. Adsorption isotherm data were better fitted by the Freundlich model (R 2 is 0.94) than the Langmuir model (R 2 is 0.85). Thermodynamic study showed that the adsorption process is endothermic and mainly physical in nature with the values of H 0 being 48.0 kJ/mol, S 0 being 157.1 J/mol/K, and G 0 varying from 1.02 to −2.14 kJ/mol. The graphite-like structure in biochar enables the π-π interactions with a ring structure in the TC molecule, which, together with the N-6 acting as electron donor, is the main driving force of the adsorption process.
Penelitian ini bertujuan untuk mengetahui pengaruh kecepatan superfisial liquid (VSL) dan kecepatan superfisial gas (VSG) terhadap karakteristik (visualisasi pola aliran stratified, frekuensi hydraulic jump dan kecepatan hydraulic jump) dan parameter (fraksi hampa, liquid holdup dan gradien penurunan tekanan) pola aliran stratified pada aliran airudarapipa horizontal. Metode yang digunakan adalah eksperimental dengan pengujian variasi kecepatan superfisial liquid (VSL) dan kecepatan superfisial gas (VSG) yang dianalisa menggunakan metode image processing. Pengambilan data menggunakan high speed video camera dengan kecepatan 400 fps. Penelitian ini menggunakan pipa acrylic transparan berdiameter dalam 19 mm dan mempunyai penampang berbentuk lingkaran. Posisi pipa dalam keadaan horisontal dengan fluida air sebagai liquid dan udara sebagai gas. Penelitian ini dilakukan dengan asumsi temperatur ruang konstan. Hasil penelitian diperoleh kecepatan superfisial liquid dan gas yang optimal untuk menghindari hydraulic jump pada pengaplikasian industri dengan peningkatan maksimal kecepatan superfisial liquid (VSL) adalah 0,064 mâ„s dan kecepatan superfisial gas (VSG) adalah 3,254 mâ„s, untuk peningkatan VSL= 0,050 mâ„s maksimal peningkatan VSG = 4,140 mâ„. Penelitian ini menjelaskan perubahan kecepatan superfisial liquid (VSL) dan kecepatan superfisial gas (VSG) mempengaruhi karakteristik dan paramater pola aliran stratified. Hal ini ditunjukkan dengan berubahnya visualisasi bentuk pola aliran, nilai frekuensi hydraulic jump, kecepatan hydraulic jump, fraksihampa, liquid holdup dan gradien tekanan.
This study was aimed at determining the influence of the number of blades and water velocity on the performance of vertical axis water turbine type Helical Gorlov. The method used was an experimental method. The descriptive analysis method was also used to analyze the data. The data obtained were in the form of variations of blades number and water velocity. The variations in the number of blades used were 2 blades, 3 blades, and 4 blades. While water velocity variations used were 0.81 m / s, 0.94 m / s, 1.08 m / s, and 1.18 m / s. The parameters were used to measure the amount of current and voltage produced by the multimeter and the number of rotations per minute (rpm) of the turbine produced by the tachometer. The results show that the number of blades and water velocity affected the performance of the Gorlov helical water turbine. The most optimal Gorlov helical turbine based on the results of research with the highest power coefficient (Cp) value is a turbine with 2 blades at a water velocity of 0.94 m/s which produces a Cp value of 0.00376 and a TSR value of 1.35.PENGARUH JUMLAH SUDU DAN KECEPATAN AIR TERHADAP KINERJA TURBIN AIR SUMBU VERTIKAL TIPE HELIKS GORLOVPenelitian ini bertujuan untuk pengaruh jumlah sudu dan kecepatan air terhadap kinerja turbin air sumbu vertikal tipe Heliks Gorlov. Metode yang digunakan dalam penelitian ini adalah eksperimen. Penelitian ini menggunakan analisis deskriptif.Data yang duperoleh berupa variasi jumlah sudu dan variasi kecepatan air. Variasi jumlah sudu yang digunakan adalah 2 sudu, 3 sudu, dan 4 sudu. Variasi kecepatan air yang digunakan yaitu 0,81 m/s, 0,94 m/s, 1,08 m/s, dan 1,18 m/s. Parameter dalam penelitian ini yang digunakan untuk menentukan kinerja adalah mengukur besarnya arus dan tegangan yang dihasilkan multimeter dan banyaknya rotasi per menit (rpm) dari turbin yang dihasilkan tachometer.Hasil penelitian menunjukkan bahwa jumlah sudu dan kecepatan air mempengaruhi kinerja turbin air heliks gorlov. Kedua, kecepatan air mempengaruhi kinerja turbin air heliks gorlov.Turbin heliks Gorlov paling optimal berdasarkan hasil penelitian dengan nilai koefisien daya (Cp) tertinggi yaitu turbin dengan 2 sudu pada kecepatan air 0,94 m/s yang menghasilkan nilai Cp sebesar 0,00376 dan nilai TSR 1,35.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.