We describe a new technology based on thermoforming as a microfabrication process. It significantly enhances the tailoring of polymers for three dimensional tissue engineering purposes since for the first time highly resolved surface and bulk modifications prior to a microstructuring process can be realised. In contrast to typical micro moulding techniques, the melting phase is avoided and thus allows the forming of pre-processed polymer films. The polymer is formed in a thermoelastic state without loss of material coherence. Therefore, previously generated modifications can be preserved. To prove the feasibility of our newly developed technique, so called SMART = Substrate Modification And Replication by Thermoforming, polymer films treated by various polymer modification methods, like UV-based patterned films, and films modified by the bombardment with energetic heavy ions, were post-processed by microthermoforming. The preservation of locally applied specific surface and bulk features was demonstrated e.g. by the selective adhesion of cells to patterned microcavity walls.
We describe a multi-purpose platform for the three-dimensional cultivation of tissues. The device is composed of polymer chips featuring a microstructured area of 1-2 cm(2). The chip is constructed either as a grid of micro-containers measuring 120-300 x 300 x 300 microm (h x l x w), or as an array of round recesses (300 microm diameter, 300 microm deep). The micro-containers may be separately equipped with addressable 3D-micro-electrodes, which allow for electrical stimulation of excitable cells and on-site measurements of electrochemically accessible parameters. The system is applicable for the cultivation of high cell densities of up to 8 x 10(6) cells and, because of the rectangular grid layout, allows the automated microscopical analysis of cultivated cells. More than 1000 micro-containers enable the parallel analysis of different parameters under superfusion/perfusion conditions. Using different polymer chips in combination with various types of bioreactors we demonstrated the principal suitability of the chip-based bioreactor for tissue culture applications. Primary and established cell lines have been successfully cultivated and analysed for functional properties. When cells were cultured in non-perfused chips, over time a considerable degree of apoptosis could be observed indicating the need for an active perfusion. The system presented here has also been applied for the differentiation analysis of pluripotent embryonic stem cells and may be suitable for the analysis of the stem cell niche.
This paper presents a fundamentally new approach for the manufacturing and the possible applications of lab on a chip devices, mainly in the form of disposable fluidic microchips for life sciences applications. The new technology approach is based on a novel microscale thermoforming of thin polymer films as core process. The flexibility not only of the semi-finished but partly also of the finished products in the form of film chips could enable future reel to reel processes in production but also in application. The central so-called 'microthermoforming' process can be surrounded by pairs of associated pre- and postprocesses for micro- and nanopatterned surface and bulk modification or functionalisation of the formed films. This new approach of microscale thermoforming of thin polymer film substrates overlaid with a split local modification of the films is called 'SMART', which stands for 'substrate modification and replication by thermoforming'. In the process, still on the unformed, plane film, the material modifications of the preprocess define the locations where later, then on the spatially formed film, the postprocess generates the final local modifications. So, one can obtain highly resolved modification patterns also on hardly accessible side walls and even behind undercuts. As a first application of the new technology, we present a flexible chip-sized scaffold for three dimensional cell cultivation in the form of a microcontainer array. The spatially warped container walls have been provided with micropores, cell adhesion micropatterns and thin film microelectrodes.
The CellChip is a microstructured polymer scaffold, which favours a three-dimensional cultivation of cells within an array of cubic microcontainers. The manufacturing process used so far is microinjection moulding combined with laser-based perforation. In a first attempt to simplify the process, costly perforation was avoided by using commercially available, inexpensive microfiltration membranes for the bottom of the microcavities. Microthermoforming is a promising novel technique which allows the CellChip to be produced from thin film. Working pressures of approximately 4000 kPa were required for the adequate moulding of 50 microm thick films from three different polymers (polystyrene, polycarbonate, cyclo-olefin polymer). Integrating drafts and chamfers in micromoulds is not going to eliminate an uneven thickness profile, but reduces demoulding forces. Microthermoformed CellChips of polycarbonate were perforated by an ion track technique to guarantee a sufficient supply of medium and gases to the cells. The prestructured CellChips were irradiated with 1460 MeV xenon ions at a fluence of a few 10(6) ions/cm2. The tracks were etched in an aqueous solution of 5 N NaOH at 30 degrees C, which resulted in cylindrical pores approximately 2 microm in diameter. Microinjection-moulded, membrane-bonded and thermoformed CellChips were subjected to comparative examination for viability in a cell culture experiment with parenchymal liver cells (HepG2). The cells stayed viable over a period of more than 20 days. No significant differences in viability between injection-moulded, membrane-bonded, and thermoformed CellChips were observed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.