Submarine gas hydrate is a hazard to drilling, a potential hydrocarbon resource, and has been implicated as a factor in both submarine slope stability and climate change. Bulk in situ electrical resistivities evaluated from electromagnetic surveys have the potential to provide an estimate of the total hydrate volume fraction more directly than by using seismic and well log data. We conducted a marine controlled‐source electromagnetic sounding at Hydrate Ridge, Oregon, USA, in August, 2004. Electromagnetic fields transmitted by a deep‐towed horizontal electric dipole source were measured by a linear array of 25 seafloor electromagnetic receivers, positioned 600 m apart to produce a dense coverage in the recorded electric field data. Results are presented in simple form by apparent resistivity pseudosections, which produce an approximate image of lateral resistivity variations across the study region. Resistivity values are consistent with those from well logs collected in the area and pseudosection features are correlated with seismic reflectors. Archie's Law, based on pseudosection apparent resistivities, predicts volumetric hydrate concentrations vary from 0–30% across the ridge.
We acquired coincident marine controlled source electromagnetic (CSEM), high‐resolution seismic reflection and ocean‐bottom seismometer (OBS) data over an active pockmark in the crest of the southern part of the Vestnesa Ridge, to estimate fluid composition within an underlying fluid‐migration chimney. Synthetic model studies suggest resistivity obtained from CSEM data can resolve gas or hydrate saturation greater than 5% within the chimney. Acoustic chimneys imaged by seismic reflection data beneath the pockmark and on the ridge flanks were found to be associated with high‐resistivity anomalies (+2–4 Ωm). High‐velocity anomalies (+0.3 km/s), within the gas‐hydrate stability zone (GHSZ) and low‐velocity anomalies (−0.2 km/s) underlying the GHSZ, were also observed. Joint analysis of the resistivity and velocity anomaly indicates pore saturation of up to 52% hydrate with 28% free gas, or up to 73% hydrate with 4% free gas, within the chimney beneath the pockmark assuming a nonuniform and uniform fluid distribution, respectively. Similarly, we estimate up to 30% hydrate with 4% free gas or 30% hydrate with 2% free gas within the pore space of the GHSZ outside the central chimney assuming a nonuniform and uniform fluid distribution, respectively. High levels of free‐gas saturation in the top part of the chimney are consistent with episodic gas venting from the pockmark.
We have developed a three‐axis electric field receiver designed to be towed behind a marine electromagnetic transmitter for the purpose of mapping the electrical resistivity in the upper 1000 m of seafloor geology. By careful adjustment of buoyancy and the use of real‐time monitoring of depth and altitude, we are able to deep‐tow multiple receivers on arrays up to 1200 m long within 50 m of the seafloor, thereby obtaining good coupling to geology. The rigid body of the receiver is designed to reduce noise associated with lateral motion of flexible antennas during towing, and allows the measurement of the vertical electric field component, which modeling shows to be particularly sensitive to near‐seafloor resistivity variations. The positions and orientations of the receivers are continuously measured, and realistic estimates of positioning errors can be used to build an error model for the data. During a test in the San Diego Trough, offshore California, inversions of the data were able to fit amplitude and phase of horizontal electric fields at three frequencies on three receivers to about 1% in amplitude and 1° in phase and vertical fields to about 5% in amplitude and 5° in phase. The geological target of the tests was a known cold seep and methane vent in 1000 m water depth, which inversions show to be associated with a 1 km wide resistor at a depth between 50 and 150 m below seafloor. Given the high resistivity (30 Ωm) and position within the gas hydrate stability field, we interpret this to be massive methane hydrate.
[1] Electromagnetic (EM) remote-sensing techniques are demonstrated to be sensitive to gas hydrate concentration and distribution and complement other resource assessment techniques, particularly seismic methods. To fully utilize EM results requires knowledge of the electrical properties of individual phases and mixing relations, yet little is known about the electrical properties of gas hydrates. We developed a pressure cell to synthesize gas hydrate while simultaneously measuring in situ frequency-dependent electrical conductivity (s). Synthesis of methane (CH 4 ) hydrate was verified by thermal monitoring and by post run cryogenic scanning electron microscope imaging. Impedance spectra (20 Hz to 2 MHz) were collected before and after synthesis of polycrystalline CH 4 hydrate from polycrystalline ice and used to calculate s. We determined the s of CH 4 hydrate to be 5 × 10 −5 S/m at 0°C with activation energy (E a ) of 30.6 kJ/mol (−15 to 15°C). After dissociation back into ice, s measurements of samples increased by a factor of ∼4 and E a increased by ∼50%, similar to the starting ice samples.
S U M M A R YGas hydrates are a potential energy resource and hazard for drilling and infrastructure, yet estimates of global volume vary by over three orders of magnitude. Hydrates are electrically resistive compared to water saturated sediment and so electromagnetic methods provide an additional tool to seismic surveys and drilling for determining hydrate saturations. A marine electromagnetic survey was carried out at Hydrate Ridge, Oregon, USA, with the aim of testing the use of controlled source electromagnetic (CSEM) and magnetotelluric (MT) methods to map gas hydrate and free gas below the gas hydrate stability zone. A 2-D CSEM inversion supports the scenario deduced from previous seismic and drilling results, which indicate two mechanisms of hydrate emplacement: a transport-dominated and reaction-dominated regime. A prominent resistive region of 2.5-4 m at a depth of about 130 mbsf, near the seismic bottom simulating reflector (BSR), suggests that 27 to 46 per cent of the bulk volume is filled with hydrate, depending on whether Archie's Law or the Hashin-Strikman bounds are used. This is representative of a reaction-dominated regime for hydrate emplacement, and where a significant low velocity zone exists based on a seismic tomography inversion, suggests large quantities of free gas below the BSR. Electrical resistivity logging while drilling (LWD) data show general agreement with the CSEM inversion model except for a CSEM-derived resistive region at seismic horizon A, known to transport free gas into the gas hydrate stability zone. Inversion of MT data collected simultaneously during the CSEM survey provides a complimentary low-resolution image of the shallow sediments and shows folding in the accretionary complex sediments similar to that imaged by a tomographic seismic velocity model.
S U M M A R YThe Arctic continental margin contains large amounts of methane in the form of methane hydrates. The west Svalbard continental slope is an area where active methane seeps have been reported near the landward limit of the hydrate stability zone. The presence of bottom simulating reflectors (BSRs) on seismic reflection data in water depths greater than 600 m suggests the presence of free gas beneath gas hydrates in the area. Resistivity obtained from marine controlled source electromagnetic (CSEM) data provides a useful complement to seismic methods for detecting shallow hydrate and gas as they are more resistive than surrounding water saturated sediments. We acquired two CSEM lines in the west Svalbard continental slope, extending from the edge of the continental shelf (250 m water depth) to water depths of around 800 m. High resistivities (5-12 m) observed above the BSR support the presence of gas hydrate in water depths greater than 600 m. High resistivities (3-4 m) at 390-600 m water depth also suggest possible hydrate occurrence within the gas hydrate stability zone (GHSZ) of the continental slope. In addition, high resistivities (4-8 m) landward of the GHSZ are coincident with high-amplitude reflectors and low velocities reported in seismic data that indicate the likely presence of free gas. Pore space saturation estimates using a connectivity equation suggest 20-50 per cent hydrate within the lower slope sediments and less than 12 per cent within the upper slope sediments. A free gas zone beneath the GHSZ (10-20 per cent gas saturation) is connected to the high free gas saturated (10-45 per cent) area at the edge of the continental shelf, where most of the seeps are observed. This evidence supports the presence of lateral free gas migration beneath the GHSZ towards the continental shelf.
Knowledge of the electrical properties of multicomponent systems with gas hydrate, sediments, and pore water is needed to help relate electromagnetic (EM) measurements to specific gas hydrate concentration and distribution patterns in nature. Toward this goal, we built a pressure cell capable of measuring in situ electrical properties of multicomponent systems such that the effects of individual components and mixing relations can be assessed. We first established the temperature‐dependent electrical conductivity (σ) of pure, single‐phase methane hydrate to be ~5 orders of magnitude lower than seawater, a substantial contrast that can help differentiate hydrate deposits from significantly more conductive water‐saturated sediments in EM field surveys. Here we report σ measurements of two‐component systems in which methane hydrate is mixed with variable amounts of quartz sand or glass beads. Sand by itself has low σ but is found to increase the overall σ of mixtures with well‐connected methane hydrate. Alternatively, the overall σ decreases when sand concentrations are high enough to cause gas hydrate to be poorly connected, indicating that hydrate grains provide the primary conduction path. Our measurements suggest that impurities from sand induce chemical interactions and/or doping effects that result in higher electrical conductivity with lower temperature dependence. These results can be used in the modeling of massive or two‐phase gas‐hydrate‐bearing systems devoid of conductive pore water. Further experiments that include a free water phase are the necessary next steps toward developing complex models relevant to most natural systems.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.