Recently, cylinder liners of automotive and aircraft engines are encountered severe wear due to piston slap occurred by the repeated sliding stroke of piston. This research focuses on providing an alternative material for cylinder liners, which can be obtained through friction stir processing on AA7075 with different weight ratios of reinforcements like Al2O3 and SiC. Friction stir processing is executed with a tool rotational speed of 1000 r/min and traveling speed of 56 mm/min at 2° tool tilt angle. The images of optical microscopy reveal the fine-grains with a homogeneous distribution of secondary phase particles and also offer decrement in particle clustering except at some localized regions. It is identified that addition of 3.7 wt.% Al2O3 + 3.0 wt.% SiC in AA7075 enhanced the microhardness about 33.96% higher than base matrix. Hence, wear resistance of the specimen is improved. Dry sliding wear behavior of specimens is analyzed using pin on disc at 20, 40, and 60 N load conditions to create the actual sliding behavior of piston on cylinder wall. Increasing the wt.% of Al2O3 particles enhanced the wear resistance of AA7075 surface hybrid composites at 20 N load due to the formation of protective tribofilm. Specimen with 3.7% Al2O3 + 3.0% SiC has better lubrication and load-bearing capacity that exhibits superior tribological behavior at 40 and 60 N. Higher Fe content of 5.44 wt.% has been obtained through spectroscopy analysis in S5, which is 8% and 6% higher than S3 (7.5% of Al2O3) and S7 (6% of SiC), respectively. The scratching action of this hard specimen on the counterpart brings more Fe content. Increase of Al2O3 particles paved the way for tribofilm formation and identified through scanning electron microscopy micrographs. The observation from worn specimens shows that finer wear debris had increased by adding more quantity of SiC particles due to abrasive wear mechanism.
Purpose
This paper aims to overcome the corrosion in AA7075 by incorporating the dual-reinforcements like Al2O3 and SiC through friction stir processing (FSP). In recent days, an automotive monocoque structure undergoes corrosion because of changes in environmental conditions.
Design/methodology/approach
Surface hybrid composites (SHCs) of AA7075 with different weight ratios of Al2O3 and SiC were fabricated at a rotating speed of 1000 rpm, traveling speed of 56 mm/min and tool tilt angle of 2º with two passes. Surface regions were observed using optical microscopy, and the potentiodynamic corrosion test was performed under a 3.5 per cent NaCl environment at room temperature. Then, the surface morphology analysis of corroded samples and their structural properties were also investigated through scanning electron microscopy (SEM), X-ray diffraction (XRD) and electron dispersive spectroscopy (EDS).
Findings
Through FSP, an improved interface between the reinforced particles and the AA7075 base matrix was observed because of the severe plastic deformation. Potentiodynamic polarization tests confirmed that the AA7075 matrix with a higher concentration of Al2O3 and a lower concentration of SiC (Al2O3 – 75 per cent and SiC – 25 per cent) possesses a lower corrosion rate than other specimens. This result is because of the combined effect of stable passive film formation and the resistance produced by hard SiC particles. In addition, the formation of a stronger interface between the reinforcements and the base matrix impedes the NaCl solution attack. The SEM micrograph depicts the film crystallinity variations with an increase in Al2O3 content. Debonding between the layers was observed on increasing the SiC content in the base matrix. XRD shows the peaks of reinforcing elements that influence the corrosion behavior. These observations suggest that the AA7075 reinforced with a higher concentration of Al2O3 and a lower concentration of SiC through FSP affords a suitable solution for automotive monocoque applications.
Originality/value
The corrosion rate has been identified for AA7075 SHCs with various concentrations of Al2O3 and SiC and has been compared with that of the base metal and the friction stir processed specimen without reinforcement.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.