Formation and avoidance of M–M bonds in the clathrate framework result in extreme structural complexity.

Research on the National Spherical Torus Experiment, NSTX, targets physics understanding needed for extrapolation to a steady-state ST Fusion Nuclear Science Facility, pilot plant, or DEMO. The unique ST operational space is leveraged to test physics theories for next-step tokamak operation, including ITER. Present research also examines implications for the coming device upgrade, NSTX-U. An energy confinement time, τ E , scaling unified for varied wall conditions exhibits a strong improvement of B T τ E with decreased electron collisionality, accentuated by lithium (Li) wall conditioning. This result is consistent with nonlinear microtearing simulations that match the experimental electron diffusivity quantitatively and predict reduced electron heat transport at lower collisionality. Beam-emission spectroscopy measurements in the steep gradient region of the pedestal indicate the poloidal correlation length of turbulence of about ten ion gyroradii increases at higher electron density gradient and lower T i gradient, consistent with turbulence caused by trapped electron instabilities. Density fluctuations in the pedestal top region indicate ion-scale microturbulence compatible with ion temperature gradient and/or kinetic ballooning mode instabilities. Plasma characteristics change nearly continuously with increasing Li evaporation and edge localized modes (ELMs) stabilize due to edge density gradient alteration. Global mode stability studies show stabilizing resonant kinetic effects are enhanced at lower collisionality, but in stark contrast have almost no dependence on collisionality when the plasma is off-resonance. Combined resistive wall mode radial and poloidal field sensor feedback was used to control n = 1 perturbations and improve stability. The disruption probability due to unstable resistive wall modes (RWMs) was surprisingly reduced at very high β N /l i > 10 consistent with low frequency magnetohydrodynamic spectroscopy measurements of mode stability. Greater instability seen at intermediate β N is consistent with decreased kinetic RWM stabilization. A model-based RWM state-space controller produced long-pulse discharges exceeding β N = 6.4 and β N /l i = 13. Precursor analysis shows 96.3% of disruptions can be predicted with 10 ms warning and a false positive rate of only 2.8%. Disruption halo currents rotate toroidally and can have significant toroidal asymmetry. of this phenomenon in designing future RF systems. The snowflake divertor configuration enhanced by radiative detachment showed large reductions in both steady-state and ELM heat fluxes (ELMing peak values down from 19 MW m −2 to less than 1.5 MW m −2 ). Toroidal asymmetry of heat deposition was observed during ELMs or by 3D fields. The heating power required for accessing H-mode decreased by 30% as the triangularity was decreased by moving the X-point to larger radius, consistent with calculations of the dependence of E × B shear in the edge region on ion heat flux and X-point radius. Co-axial helicity injection reduced the induct...

Biomass fuel is the most common energy source for cooking and space heating in developing countries. Biomass fuel combustion causes high levels of indoor air pollutants including particulates and other combustion by-products. We measured indoor air quality in 23 houses with a wood burning stove in rural residential areas of Costa Rica. Daily PM2.5, PM10 and CO concentrations, and particle size distribution were simultaneously measured in the kitchen. When a wood burning stove was used during the monitoring period, average daily PM2.5 and PM10 concentrations were 44 and 132 microg/m3, respectively. Average CO concentrations were between 0.5 and 3.3 ppm. All houses had a particle size distribution of either one or two peaks at around 0.7 and 2.5 microm aerodynamic diameters. The particulate levels increased rapidly during cooking and decreased quickly after cooking. The maximum peak particulate levels ranged from 310 to 8170 microg/m3 for PM2.5 and from 500 to 18900 microg/m3 for PM10 in all houses. Although the 24-h particulate levels in this study are lower than the National Ambient Air Quality Standards of PM2.5 and PM10, it is important to note that people, especially women and children, are exposed to extremely high levels of particulates during cooking.