Nanocomposites comprising high-density polyethylene (HDPE) and boehmite (BA) nanoparticles were prepared by melt blending and subsequently irradiated with electrons. Electron irradiation of HDPE causes crosslinking and, in the presence of BA, generates ketone functional groups. The functional groups can then form hydrogen bonds with the hydroxyl groups on the surface of the BA. Additionally, if the BA is surface modified by vinyltrimethoxysilane (vBA), it can covalently bond with the HDPE by irradiation-induced radical grafting. The strong covalent bonds generated by electron beam irradiation allow the desirable properties of the nanofiller to be transferred to the rest of the nanocomposite. Since EB irradiation produces a great number of strong covalent bonds between vBA nanoparticles and HDPE, the modulus of elasticity, yield strength, and resistance to thermal shrinkage are enhanced by electron irradiation.
The effect of scintillator particle size on high-resolution X-ray imaging was studied using zinc tungstate (ZnWO4) particles. The ZnWO4 particles were fabricated through a solid-state reaction between zinc oxide and tungsten oxide at various temperatures, producing particles with average sizes of 176.4 nm, 626.7 nm, and 2.127 μm; the zinc oxide and tungsten oxide were created using anodization. The spatial resolutions of high-resolution X-ray images, obtained from utilizing the fabricated particles, were determined: particles with the average size of 176.4 nm produced the highest spatial resolution. The results demonstrate that high spatial resolution can be obtained from ZnWO4 nanoparticle scintillators that minimize optical diffusion by having a particle size that is smaller than the emission wavelength.
A new concept for a non-destructive testing device using a novel carbon nanotube (CNT) based miniature x-ray tube is proposed. The device can be used for small-scale internal inspection of objects. To investigate the effectiveness of the proposed concept, the device was fabricated and its performance was systematically analyzed. The non-destructive testing device consists of a CNT based miniature x-ray tube, a scintillator, an optical lens, and a detector. The size of the focal spot needed to identify objects as small as 5 µm was calculated through simulation. An electron optics simulation software, E-GUN, was used to optimize the geometries of both the focusing cup and the x-ray target to achieve the desired focal spot size of the x-ray tube. The CNT based miniature x-ray tube was fabricated using the brazing process, and an NdFeB focusing lens was used to further reduce the focal spot size. XR images were obtained using the fabricated device and the spatial resolutions of the images were evaluated using the modulation transfer function (MTF). The fields of view (FOVs) per probe are 7.1 mm2 and 1.8 mm2 when using a 5× optical lens and a 10× optical lens, respectively. The FOV can be increased by increasing the number of probes incorporated into the device. MTF10 values were determined to be 105 lp/mm and 230 lp/mm when using the 5× optical lens and 10× optical lens, respectively. By using an optical lens to enlarge the XR images, the effect of focal spot was minimized and clear XR images were obtained.
Purpose: We designed and fabricated a surface applicator of a novel carbon nanotube (CNT)-based miniature X-ray tube for the use in superficial electronic brachytherapy of skin cancer. To investigate the effectiveness of the surface applicator, the performance of the applicator was numerically and experimentally analyzed. Methods: The surface applicator consists of a graphite flattening filter and an X-ray shield. A Monte Carlo radiation transport code, MCNP6, was used to optimize the geometries of both the flattening filter and the shield so that X-rays are generated uniformly over the desired region. The performance of the graphite filter was compared with that of conventional aluminum (Al) filters of different geometries using the numerical simulations. After fabricating a surface applicator, the X-ray spatial distribution was measured to evaluate the performance of the applicator.Results: The graphite filter shows better spatial dose uniformity and less dose distortion than Al filters. Moreover, graphite allows easy fabrication of the flattening filter due to its low X-ray attenuation property, which is particularly important for low-energy electronic brachytherapy. The applicator also shows that no further X-ray shielding is required for the application because unwanted X-rays are completely protected. As a result, highly uniform X-ray dose distribution was achieved from the miniature X-ray tube mounted with the surface applicators. The measured values of both flatness and symmetry were less than 5% and the measured penumbra values were less than 1 mm. All these values satisfy the currently accepted tolerance criteria for radiation therapy. Conclusions: The surface applicator exhibits sufficient performance capability for their application in electronic brachytherapy of skin cancers.
Facile approaches for creating thin-film scintillators with high spatial resolutions and variable shapes are required to broaden the applicability of high-resolution X-ray imaging. In this study, a transparent nano-polycrystalline ZnWO4 thin-film scintillator was fabricated by thermal evaporation for high-resolution X-ray imaging. The scintillator is composed of nano-sized grains smaller than the optical wavelength range to minimize optical scattering. The high transparency of the scintillators affords a sufficiently high spatial resolution to resolve the 2 μm line and space patterns when used in a high-resolution X-ray imaging system with an effective pixel size of 650 nm. The thermal evaporation method is a convenient approach for depositing thin and uniform films on complex substrates. ZnWO4 thin-film scintillators with various shapes, such as pixelated and curved, were fabricated via thermal evaporation. The results show that the transparent nano-polycrystalline ZnWO4 thin-film scintillator deposited through thermal evaporation has a potential for use in various high-resolution X-ray imaging applications.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.