This paper presents an experimentally-proved hydrometallurgical process for selective metals recovery from the waste-printed circuit boards (WPCBs) using a combination of conventional and time-saving methods: leaching, cementation, precipitation, reduction and electrowinning. According to the results obtained in the laboratory tests, 92.4% Cu, 98.5% Pb, 96.8% Ag and over 99% Au could be selectively leached and recovered using mineral acids: sulfuric, nitric and aqua regia. Problematic tin recovery was addressed with comprehensive theoretical and experimental work, so 55.4% of Sn could be recovered through the novel physical method, which consists of two-step phase separation. Based on the results, an integral hydrometallurgical route for selective base and precious metals recovery though consecutive steps, (i) Cu, (ii) Sn, (iii) Pb and Ag, and (iv) Au, was developed. The route was tested at scaled-up laboratory level, confirming feasibility of the process and efficiencies of metals recovery. According to the obtained results, the proposed hydrometallurgical route represents an innovative and promising method for selective metals recovery from WPCBs, particularly applicable in small scale hydrometallurgical environments, focused on medium and high grade WPCBs recycling.

No abstract

In order to reflect possible issues in future sole e-waste processing, an electrolyte of complex chemical composition reflecting system of sole e-waste processing was obtained by following a specially designed pyro-electrometallurgical method. The obtained non-standard electrolyte was further used for the purpose of comprehensive metal interference evaluation on the copper solvent extraction (SX) process. Optimization of the process included a variation of several process parameters, allowing determination of the effect of the most abundant and potentially the most influential impurities (Ni, Sn, Fe, and Zn) and 14 other trace elements. Moreover, comparing three commercial extractants of different active chelating groups, it was determined that branched aldoxime reagent is favorable for Cu extraction from the chemically complex system, as can be expected in future e-waste recycling. The results of this study showed that, under optimal conditions of 20 vol.% extractant concentration, feed pH 1.5, O/A ratio 3, and 10-min phase contact time, 88.1% of one stage Cu extraction was achieved. Co-extraction of the Fe, Zn, Ni, and Sn was under 8%, while Pb and trace elements were negligible. Optimal conditions (H2SO4 180 g/L, O/A = 2, and contact time 5 min) enabled 95.3% Cu stripping and under 6% of the most influential impurities. In addition, an impurity monitoring and distribution methodology enabled a better understanding and design of the process for the more efficient valorization of metals from e-waste.

Background: Transarterial chemoembolisation (TACE) is the primary treatment for intermediate-stage hepatocellular carcinoma (HCC), according to the updated Barcelona Clinic Liver Cancer (BCLC) staging system. Although growing evidence favours liver resection (LR) over TACE for intermediate-stage HCC, the best treatment option remains controversial. This meta-analysis aimed to compare the overall survival (OS) after LR versus TACE for intermediate-stage HCC. Methods: A comprehensive literature review of PubMed, Embase, Cochrane Library, and Web of Science was performed. Studies that compared the efficacy of LR and TACE in patients with intermediate (BCLC stage B) HCC were selected. According to the recent updated BCLC classification, intermediate stage of HCC was defined as follows: (a) four or more HCC nodules of any size, or (b) two or three nodules, but if at least one tumour is larger than 3 cm. The main outcome was OS, expressed as the hazard ratio. Results: Nine eligible studies of 3355 patients were included in the review. The OS of patients who underwent LR was significantly longer than that of patients who underwent TACE (hazard ratio=0.52; 95% CI: 0.39–0.69; I2=79%). Prolonged survival following LR was confirmed after sensitivity analysis of five studies using propensity score matching (HR=0.45; 95% CI: 0.34–0.59; I 2=55%). Conclusion: Patients with intermediate-stage HCC who underwent LR had a longer OS that those who underwent TACE. The role of LR in patients with BCLC stage B should be clarified in future randomised controlled trials.

The aim of this study was to investigate a possibility of synthesis of porous ceramics with controlled open porosity, which could be used as sorbents and catalyst supports. Two organic additives were used to obtain open porosity: polystyrene beads and cellulose fibers, which are mixed with kaolin clay powder and the appropriate water content. Samples were sintered at 1050?C for 1h. Characterization of the obtained products included X-ray powder diffraction analysis (XRPD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and elemental CHNS analysis. In addition, porosity was examined by quantification of visual information. The specific surface areas were determined by the Brunauer-Emmett-Teller (BET) method. Also, density and compressive strength of the obtained samples were assessed. It was determined that by sintering, the organic component completely leaves the system. For samples prepared with polystyrene beads and with cellulose fibers, satisfactory mechanical properties were obtained: compressive strengths were 1.42 and 1.56 MPa, respectively. It was noted that significantly higher open porosity was obtained by using polystyrene beads as a sacrificial template (porosity of ~56 %) instead of cellulose fibers (porosity of ~6 %).