Studying noninvasively the internal nanoporous structure of a single Tussah silk fiber under different humidity conditions, we demonstrate for the first time the feasibility of in-situ ptychographic tomography. The resulting 3D images of the silk fiber interior, obtained at both dry and humid conditions, yield quantitative information about the spatial density variations in the form of detailed maps of the size, shape, and orientation distributions of the nanopores inside the silk fiber, revealing that the fiber swells anisotropically in humid conditions, with the expansion taking place solely normal to the fiber axis. Exploiting quantitative information on the fiber’s electron density, hydration was found to proceed through interaction with the silk protein rather than filling of pores.

Cobalt nanoparticles play an important role as catalysts for the Fischer− Tropsch synthesis, which is an attractive route for production of synthetic fuels. It is of particular interest to understand the varying conversion rate during the first hours after introducing synthesis gas (H 2 and CO) to the system. To this end, several in situ characterization studies have previously been done on both idealized model systems and commercially relevant catalyst nanoparticles, using bulk techniques, such as X-ray powder diffraction and X-ray absorption spectroscopy. Since catalysis takes place at the surface of the cobalt particles, it is important to develop methods to gain surface-specific structural information under realistic processing conditions. We addressed this challenge using small-angle X-ray scattering (SAXS), a technique exploiting the penetrating nature of Xrays to provide information about particle morphology during in situ experiments. Simultaneous wide-angle X-ray scattering was used for monitoring the reduction from oxide to catalytically active metal cobalt, and anomalous SAXS was used for distinguishing the cobalt particles from the other phases present. After introducing the synthesis gas, we found that the slope of the scattered intensity in the Porod region increased significantly, while the scattering invariant remained essentially constant, indicating a change in the shape or surface structure of the particles. Shape-and surface change models are discussed in light of the experimental results, leading to an improved understanding of catalytic nanoparticles. ■ INTRODUCTIONThe Fischer−Tropsch synthesis (FTS) is a set of chemical reactions that forms hydrocarbon chains from a mixture of CO and H 2 . The product can be upgraded to petroleum substitutes, for example synthetic diesel.1 Typical commercial FTS catalysts consist of cobalt nanoparticles of diameter ∼20 nm dispersed on a porous support material, 2 such as γ-alumina. Optimal particle size, temperature, and pressure are required for obtaining high activity and high selectivity to long-chain hydrocarbons. The reaction output is dependent on the temperature and the pressure in the reactor cell; the standard industrial process operates at T ≈ 220°C and pressure of 25− 45 bar, conditions favorable for producing waxes.1 At ambient pressure the CO conversion is still high, but the products are predominantly short molecules, thus tending to remain in the gas phase.The FTS shows an initial stage lasting a few hours where the conversion rate increases to a high level, followed by a much slower decrease of the reaction rate that continues on a time scale of days and months.3 Understanding the mechanisms behind this behavior is of high commercial and academic interest. Tsakoumis et al.3 combined in situ X-ray absorption spectroscopy (XAS) and X-ray powder diffraction to investigate the cobalt catalyst nanoparticles during the FTS synthesis. The deactivation was detected by mass spectrometry, but no apparent changes in the X-ray signal could be...

No abstract

Imaging nanoparticles under relevant reaction conditions of high temperature and gas pressure is difficult because conventional imaging techniques, like transmission electron microscopy, cannot be used. Here we demonstrate that the coherent diffractive imaging technique of X-ray ptychography can be used for in situ phase contrast imaging in structure studies at atmospheric pressure and elevated temperatures. Lithium zirconate, a candidate CO 2 capture material, was studied at a pressure of one atmosphere in air and in CO 2 , at temperatures exceeding 600 C. Images with a spatial resolution better than 200 nm were retrieved, and possibilities for improving the experiment are described. V

Synthesis and characterisation of tailored mesostructured alumina as thin films and powders with a narrow pore size distribution.