This article addresses the design, development, and evaluation of T-shirt prototypes that embed novel textile sensors for the capture of cardio and respiratory signals. The sensors are connected through textile interconnects to either an embedded custom-designed data acquisition and transmission unit or to snap fastener terminals for connection to external monitoring devices. The performance of the T-shirt prototype is evaluated in terms of signal-to-noise ratio amplitude and signal interference caused by baseline wander and motion artefacts, through laboratory tests with subjects in standing and walking conditions. Performance tests were also conducted in a hospital environment using a T-shirt prototype connected to a commercial three-channel Holter monitoring device. The textile sensors and interconnects were realized with the assistance of an industrial six-needle digital embroidery tool and their resistance to wear addressed with normalized tests of laundering and abrasion. The performance of these wearable systems is discussed, and pathways and methods for their optimization are highlighted.

A partially oriented melt-extruded PLA multifilament was false-twist textured to stabilize its structure. Conventional DSC analysis showed a relaxation peak at the end of glass transition. Simultaneous consideration of the TMA curve enabled us to evaluate both the relaxation and the cold crystallisation produced during the DSC scan. The periodic load applied during TMA experiments also enabled us to examine the evolution of Young’s modulus along the glass transition, relaxation and cold crystallisation phenomena. Increases in Young’s modulus and in enthalpy are related because of crystallisation. Texturing increased crystallinity and decreased cold crystallisation of PLA during the DSC scan.Postprint (published version

Polylactide multifilament yarns were textured in order to be endowed with properties of natural staple fibre yarns for textile applications. Texturing promotes the formation of stable secondary links between the macromolecular chains. A polylactide 167/68 dtex multifilament yarn was textured under different conditions. Relaxation experiments at yield, strain softening, strain hardening and just before breaking were performed. The relaxation behaviour was studied by the application of the generalized Maxwell model. The initial stress induced when stretched, the final non-relaxed stress after relaxation and the stress relaxed at different times were determined. Variations in the relaxation behaviour were related to texturing conditions and stretching.

In this article, plain weave fabrics of polyester were functionalized by means of a polymeric coating synthesized for high conductivity, using the vapor phase polymerization method. The method is considerably more efficient and sustainable than traditional wet methods and has been previously applied to synthesize poly(3, 4-ethylenedioxythiophene) in yarns and fabrics, using oxidant agents with organic solvents. In this article, aqueous oxidant solutions were used in addition to those based in ethanol, providing textile substrates with high electrical conductance. The effect of the concentration of the oxidant solution on the electrical and mechanical characteristics of the samples was investigated and correlated to their morphology, analyzed by electron microscopy imaging. A strong decrease of the sheet resistivity of the samples with the concentration of oxidant increase was obtained, while the fabrics’ original mechanical tenacity remained unchanged. The sheet resistivity of the samples could be further decreased by a factor of 5 by the application of multiple polymerization layers and was a function of the conjugated polymer content. The effect of washing/drying cycles on the electrical conductance of the samples is presented. The electrical and mechanical characteristics obtained have potential for smart textile applications such as electromagnetic shielding and physiological sensing.

Purpose -The breaking strength compromises fabric wearing out during wear of garments and is a determining parameter in their useful life. Thus, it is intended to compare the efficacy of each method concerning the understanding of results, which is, the explanation of the phenomenon, namely through statistical models which characterize abrasion strength, measured by each method, as a function of fabric assurance by simple testing (FAST) parameters. Design/methodology/approach -The simulation of abrasion mechanism was done on Martindale wear and abrasion tester, following two ways: the weight loss and two yarns breakage methods. The average weight loss of a fabric was determined among four specimens (in mg/5,000 cy). Fabric abrasion was done against a standard wool fabric under a 12 KPa pressure. In the two yarns breakage method, the number of abrasion cycles required to break two yarns is determined according to Woolmark Company TM 112 test standard. Findings -In general, no better models to explain abrasion strength by the breakage of two yarns method are achieved when FAST variables are considered respecting those based on classical ones. However, for woollen fabrics, there is an interesting model, which gathers classical and FAST variables with higher explanation: shear rigidity and polyamide composition. This allows one to conclude that this FAST parameter performs an important role in the abrasion behaviour of fabrics. Originality/value -As the abrasion consequences cause fabric degradation, a better understanding is obtained of the different abrasion stage mechanisms, which explain both evaluation methods: breakage of two yarns and weight loss. It is intended to gather conditions for a future definition of a single and comprehensive evaluation methodology of abrasion.