No abstract

Està subjecte a una llicència de Reconeixement-NoComercial-SenseObraDerivada 4.0 de Creative Commons

Està subjecte a una llicència de Reconeixement-NoComercial-SenseObraDerivada 4.

No abstract

Radiant floor heating is becoming increasingly popular in cold climates because it delivers higher comfort levels more efficiently than conventional systems. Wood is one of the surface coverings most frequently used in radiant flooring, despite the widely held belief that in terms of thermal performance it is no match for higher conductivity materials if a high energy performance is intended. Given that the highest admissible thermal resistance for flooring finishes or coverings is generally accepted to be 0.15 m2K/W, wood would appear to be a scantly appropriate choice. Nonetheless, the evaluation of the thermal performance of wooden radiant floor heating systems in conjunction with the building in terms of energy demand, thermal comfort, and start-up period, has been insufficiently explored in research. This has led to the present knowledge gap around its potential to deliver lower energy consumption and higher thermal comfort than high-thermal-conductivity materials, depending on building characteristics. This article studies the thermal performance of wood radiant floors in terms of three parameters: energy demand, thermal comfort, and start-up lag time, analysing the effect of wood properties in conjunction with building construction on each. An experimentally validated radiant floor model was coupled to a simplified building thermal model to simulate the performance of 60 wood coverings and one reference granite covering in 216 urban dwellings differing in construction features. The average energy demand was observed to be lower in the wood than in the granite coverings in 25% of the dwellings simulated. Similarly, on average, wood lagged behind granite in thermal comfort by less than 1 h/day in 50% of the dwellings. The energy demand was minimised in a significant 18% and thermal comfort maximised in 14% of the simulations at the lowest thermal conductivity value. The vast majority of the wooden floors lengthened the start-up lag time relative to granite in only 30 min or less in all the dwellings. Wood flooring with the highest thermal resistance (even over the 0.15 m2K/W cited in standard EN 1264-2) did not significantly affect the energy demand or thermal comfort. On average, wood flooring lowered energy demand by 6.4% and daily hours of thermal comfort by a mere 1.6% relative to granite coverings. The findings showed that wood-finished flooring may deliver comparable or, in some cases, higher thermal performance than high-conductivity material coverings, even when their thermal resistance is over 0.15 m2K/W. The suggestion is that the aforementioned value, presently deemed the maximum admissible thermal resistance, may need to be revised.

The Portland cement industry is presently deemed to account for around 7.4% of the carbon dioxide emitted annually worldwide. Clinker production is being reduced worldwide in response to the need to drastically lower greenhouse gas emissions. The trend began in the nineteen seventies with the advent of mineral additions to replace clinker. Blast furnace slag and fly ash, industrial by-products that were being stockpiled in waste heaps at the time, have not commonly been included in cements. Supply of these additions is no longer guaranteed, however, due to restrained activity in the source industries for the same reasons as in clinker production. The search is consequently on for other additions that may lower pollutant gas emissions without altering cement performance. In this study, bentonite, a very common clay, was used as such an addition directly, with no need for precalcination, a still novel approach that has been scantly explored to date for reinforced structural concrete with structural applications. The results of the mechanical strength and chemical resistance (to sulfates, carbonation and chlorides) tests conducted are promising. The carbonation findings proved to be of particular interest, for that is the area where cement with mineral additions tends to be least effective. In the bentonite-bearing material analysed here, however, carbonation resistance was found to be as low as or lower than that observed in plain Portland cement.

One of the major challenges facing 3D printing for construction is the technological suitability, ‘printability’, of the materials used. These cement-based materials differ from those used in other sectors, which has a series of conditioning factors that are the object of the present analysis. This article first reviews the definition of the term ‘printability’ and its constituent stages. Those stages condition the requirements to be met by cement-based materials, whether designed for other uses or developed ad hoc, and therefore the tests applicable to determine their aptitude for use in additive manufacturing for construction. That is followed by a review of the standardised tests presently in place for mortars and concretes that can be used to verify a material’s compliance with such requirements. The paper concludes with a recommendation on the advisability of developing a standard test or suite of tests to ascertain printability.

The transformation of existing buildings into Near Zero Energy Buildings or even positive energy buildings remains a major challenge. In particular, historic buildings are an important cultural heritage that, in most cases, may be rehabilitated and reused for new purposes. However, achieving higher efficiencies in those buildings presents many difficulties, since there is a need to preserve aesthetic values and minimize impact on the buildings’ initial construction. In this work, a roadmap that allows rehabilitating a building from the eighteenth century is developed, turning it into a landmark building, to be used as a museum in the near future. The procedure is based on 3D models using REVIT software and detailed energy simulations supported by a cost-optimal methodology. The results reveal how conventional methodologies shown in the literature may improve the energy performance of the buildings during the heating regime, but performance may deteriorate during the cooling season. For that reason, the present study includes the design of a night ventilation system which allows not only solving this problem but also to reducing the cooling demands by more than 43% with little additional costs. In conclusion, historic buildings (which traditionally have a high thermal mass) have increased thermal storage potential by using the structures of the buildings themselves as well as passive cooling techniques.