In this work a numerical methodology to predict the behavior of composite unidirectional laminates under high velocity impact is developed. In order to validate the model, experimental results of high velocity impacts of steel sphere against laminate coupons, were accomplished. The residual velocity in case of penetration and the damaged area in the panel are the variables chosen to validate the results obtained in the numerical methodology proposed. Finally an analysis of the influence of the projectile geometry is accomplished.
The potential of additive manufacturing to produce architected lattice structures is remarkable, but restrictions imposed by manufacturing processes lead to practical limits on the form and dimension of structures that can be produced. In the present work, the capabilities of fused filament fabrication (FFF) to produce miniature lattices were explored, as they represent an inexpensive option for the production of polymer custom-made lattice structures. First, fused filament fabrication design guidelines were tested to assess their validity for miniature unit cells and lattice structures. The predictions were contrasted with the results of printing tests, showing some discrepancies between expected outcomes and resulting printed structures. It was possible to print functional 3D miniature open cell polymer lattice structures without support, even when some FFF guidelines were infringed, i.e., recommended minimum strut thickness and maximum overhang angle. Hence, a broad range of lattice structures with complex topologies are possible, beyond the cubic-type cell arrangements. Nevertheless, there are hard limits in 3D printing of miniature lattice structures. Strut thickness, length and orientation were identified as critical parameters in miniature lattice structures. Printed lattices that did not fully comply with FFF guidelines were capable of bearing compressive loads, even if surface quality and accuracy issues could not be fully resolved. Nevertheless, 3D printed FFF lattice structures could represent an improvement compared to other additive manufacturing processes, as they offer good control of cell geometry, and does not require additional post-processing.
Fused deposition modeling represents a flexible and relatively inexpensive alternative for the production of custom-made polymer lattices. However, its limited accuracy and resolution lead to geometric irregularities and poor mechanical properties when compared with the digital design. Although the link between geometric features and mechanical properties of lattices has been studied extensively, the role of manufacturing parameters has received little attention. Additionally, as the size of cells/struts nears the accuracy limit of the manufacturing process, the interaction between geometry and manufacturing parameters could be decisive. Hence, the influence of three geometric and two manufacturing parameters on the mechanical behavior was evaluated using a fractional factorial design of experiments. The compressive behavior of two miniature lattice structures, the truncated octahedron and cubic diamond, was evaluated, and multilinear regression models for the elastic modulus and plateau stress were developed. Cell size, unit cell type, and strut diameter had the largest impact on the mechanical properties, while the influence of feedstock material and layer thickness was very limited. Models based on factorial design, although limited in scope, could be an effective tool for the design of customized lattice structures.
The accumulation of particles in a turbulent flow of incompressible air with mono-dispersed solid particles inside a 90° pipe bend was simulated using ANSYS® Fluent (CFD), taking into account the effect of gravity, drag force and a bidirectional fluid-particle coupling. An analysis of the geometrical parameters and the structures of the secondary flow generated in a curved pipe (Dean vortices) was developed, thus determining the characteristic time scales of the flow. Four Stokes numbers (Stk) were formulated, whose values are calculated and studied from the numerical simulations performed. Two different particle sizes (d1 = 50 μm y d2 = 150 μm), at two different flow conditions (Re1 = 61,500 y Re2 = 173,972), and for three curvature ratios Rc/R = 1, 4 and 8 were studied. The flow was solved using a Eulerian–Lagrangian approach with a RNG k-ε turbulence model. Once the multiphase flow was solved and validated, the distribution and maximum particle concentration inside the 90° bend were presented. Additionally, the Stk numbers were calculated to estimate the possible particle concentration level for the different system configurations (dp, Re and Rc/R). It is concluded that, if all Stk numbers are less than one, relative concentration levels reach a minimum, while for Stk numbers larger than one, an increase in the maximum concentration inside the pipe bend was noticed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.