No abstract

This paper aims to analyze the fatigue response of PLA parts manufactured through fused filament fabrication (FFF). The influence of four factors (layer height, fill density, nozzle diameter and velocity) on the fatigue performance of cylindrical specimens is studied through an L27 Taguchi experimental design. This design is run for two different infills: linear and honeycomb. Specimens have been tested on a rotating fatigue bending machine. The optimal set of parameters and levels resulting in the highest number of cycles to failure have been determined, and implemented to manufacture a second set of specimens, which have been tested at different stress levels to represent the Wöhler curve. Fill density proves to be the most influential parameter on fatigue life, followed by layer height. The tests undertaken to represent the Wöhler curve revealed that 35.8 MPa can be considered as a lower threshold of the endurance limit for this kind of specimens. This value can be useful to use these devices to manufacture human implants, as PLA is a biocompatible material. The main novelty of this paper is that no previous fatigue life assessment of PLA parts manufactured through FFF has been developed.

This paper aims to analyse the mechanical properties response of polylactic acid (PLA) parts manufactured through fused filament fabrication. The influence of six manufacturing factors (layer height, filament width, fill density, layer orientation, printing velocity, and infill pattern) on the flexural resistance of PLA specimens is studied through an L27 Taguchi experimental array. Different geometries were tested on a four-point bending machine and on a rotating bending machine. From the first experimental phase, an optimal set of parameters deriving in the highest flexural resistance was determined. The results show that layer orientation is the most influential parameter, followed by layer height, filament width, and printing velocity, whereas the fill density and infill pattern show no significant influence. Finally, the fatigue fracture behaviour is evaluated and compared with that of previous studies’ results, in order to present a comprehensive study of the mechanical properties of the material under different kind of solicitations.

The objective of this paper is to analyze the effect of the vibration-assisted ball burnishing process on the topology of AISI 1038 flat surfaces, in order to evaluate its feasibility for surface enhancement towards wear prevention and fatigue enhancement in industrial components. With that aim, an experimental campaign based on a Taguchi orthogonal matrix has been deployed. Five factors were studied, namely: preload force, number of passes, feed, initial surface texture and strategy. The topologies of the resulting burnishing patches have been acquired with a non-contact optical device, and the 3D texture parameters have been calculated to quantify the effects of burnishing. In all cases, the bearing capacity of the burnished surfaces was improved, as the proportion of core material is increased due to the deformation of the surface peaks. The initial surface state proved to be the most influential parameter on amplitude, spatial, and volumetric parameters. In all cases, a set of optimal vibration-assisted ball burnishing parameters was found for the sake of reproducibility and systematization of the process. Finally, results have been compared to the conventional ball burnishing process, observing that it presents scratch damage on the surfaces that can be prevented through assistance through vibrations.

The aim of this paper is to explore the watertightness behaviour for high pressure applications using Multi Jet Fusion technology and polyamide 12 as a material. We report an efficient solution for manufacturing functional prototypes and final parts for water pressure applications and provide manufacturing rules for engineers in the pressurized product development process for up to 10 MPa of nominal pressure. The research findings show manufacturers the possibility of using additive manufacturing as an alternative to traditional manufacturing. Water leakage was studied using different printing orientations and wall thicknesses for a range of pressure values. An industrial ball valve was printed and validated with the ISO 9393 standard as also meeting tolerance requirements. This paper is a pioneering approach to the additive manufacturing of high-performance fluid handling components. This approach solves the problem of leakage caused by porosity in additive manufacturing technologies.

• Check the metadata sheet to make sure that the header information, especially author names and the corresponding affiliations are correctly shown. • Check the questions that may have arisen during copy editing and insert your answers/corrections. • Check that the text is complete and that all figures, tables and their legends are included. Also check the accuracy of special characters, equations, and electronic supplementary material if applicable. If necessary refer to the Edited manuscript. • The publication of inaccurate data such as dosages and units can have serious consequences. Please take particular care that all such details are correct. • Please do not make changes that involve only matters of style. We have generally introduced forms that follow the journal's style. Substantial changes in content, e.g., new results, corrected values, title and authorship are not allowed without the approval of the responsible editor. In such a case, please contact the Editorial Office and return his/her consent together with the proof. • If we do not receive your corrections within 48 hours, we will send you a reminder. Please note Your article will be published Online First approximately one week after receipt of your corrected proofs. This is the official first publication citable with the DOI. Further changes are, therefore, not possible.

Currently, additive manufacturing (AM) is not limited to prototype manufacturing, but is also used to generate parts with final applications. This paper considers this aspect of 3D printing, and aims to characterize fatigue life of parts manufactured through fused filament fabrication. This is one of the most complex AM technologies, due to the high number of parameters that must be taken into account. The knowledge of the influence of the different manufacturing parameters on the mechanical behavior of the parts has been previously considered for static forces, but so far, dynamic working regimes have not been explored. In this paper, a design of experiments through Taguchi orthogonal arrays is applied to analyze the influence of five factors on fatigue life on PLA specimens. Five fatigue tests are performed for each combination of parameters. Results show that fill density, nozzle diameter and layer height are the most influential factors on fatigue lifespan. Finally, honeycomb proves to be the most beneficial infill pattern with regards to fatigue life.Peer ReviewedPostprint (published version

No abstract