Polymeric building blocks containing terminal azide and alkyne functionalities are prepared via atom transfer radical polymerization (ATRP) and used to modularly synthesize block copolymers via 1,3-dipolar cycloaddition reactions, which are quantitative according to SEC measurements.
Polymersomes, composed of amphiphilic polystyrene-block-poly(acrylic acid) (PS-b-PAA), with the periphery being covered with azide groups, were used for further functionalization using "click" chemistry.
Biohybrid amphiphiles have been prepared from terminal azide functionalised polystyrene and an alkyne functionalised peptide or protein via a Cu(I) catalysed Huisgen [3 + 2] dipolar cycloaddition reaction.
Heterotelechelic polystyrene (PS), poly(tert‐butyl acrylate) (PtBA), and poly (methyl acrylate) (PMA), containing both azide and triisopropylsilyl (TIPS) protected acetylene end groups, were prepared in good control (Mw/Mn ≤ 1.24) by atom transfer radical polymerization (ATRP). The end groups were independently applied in two successive “click” reactions, that is: first the azide termini were functionalized and, after deprotection, the acetylene moieties were utilized for a second conjugation step. As a proof of concept, PS was consecutively functionalized with propargyl alcohol and azidoacetic acid, as confirmed by MALDI‐ToF MS. In addition, the same methodology was employed to modularly build up an ABC type triblock terpolymer. Size exclusion chromatography measurements demonstrated first coupling of PtBA to PS and, after the deprotection of the acetylene functionality on PS, connection of PMA, yielding a PMA‐b‐PS‐b‐PtBA triblock terpolymer. The reactions were driven to completion using a slight excess of azide functionalized polymers. Reduction of the residual azide groups into amines allowed easy removal of this excess of polymer by column chromatography. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2913–2924, 2007
Amphiphilic block copolymers have the ability to assemble into multiple morphologies in solution. Depending on the length of the hydrophilic block, the morphology can vary from spherical micelles, rods, and vesicles to large compound micelles (LCMs). Vesicle formation is favored upon an increase in total molecular weight of the block copolymer, that is, an increasing bending modulus (K). Owing to the polymeric character of this type of vesicle (also called polymersomes), they possess remarkable properties. The diffusion of (polymeric) amphiphiles in these vesicles is very low compared to liposomes and for high-molecular-weight chain entanglements even lead to reptation-type motions, which make it possible to trap near-equilibrium and metastable morphologies. Additionally, in contrast to liposomes, membrane thicknesses can exceed 200 nm. As a consequence, this increased membrane thickness, in combination with the conformational freedom of the polymer chains, leads to a much lower permeability for water of block copolymer vesicles compared to liposomes. The enhanced toughness and reduced permeability of polymersomes makes them, therefore, very suitable as stable nanocontainers, which can be used, for example, as reactors or drug delivery vehicles.Self-assembly of amphiphilic block copolymers in solution has been a topic of active research for more than 30 years. The most commonly observed morphology in these systems is the star-micelle. "Star" refers to the fundamental core-corona structure, which consists of a small core and a large corona. These star-micelles can be divided into regular and reversed micelles, which are formed in polar and apolar solvents, respectively.Over the past few years, the ability of highly asymmetric, amphiphilic block copolymers to assemble into aggregates of multiple morphologies in solution has attracted much attention. For these "crew-cut" aggregates, a term proposed by Halperin et al. [1], the longer block forms the core of the aggregate, while the corona is composed of the short segment. Manipulation of the relative block lengths and environmental parameters, such as solvent composition, the presence of additives, and temperature, has resulted in a variety of morphologies, including spheres, rods, vesicles, lamellae, tubules, large compound micelles (LCMs), large compound vesicles (LCVs), and hexagonally packed hollow hoops (HHHs).Several of these block copolymer morphologies are classified as vesicles because they all have hollow-spherical structures containing walls composed of bilayers of polymer molecules. The field of block copolymer vesicles (polymersomes) has only recently been explored. The earliest reports on polymersomes focused on vesicles prepared from bulk copolymer systems [2] and block copolymer/homo-
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.