No abstract

Photoemission and ab initio theoretical study of interface and film formation during epitaxial growth and annealing of praseodymium oxide on Si (001)

A highly processable, new semiconducting polymer, PCDTTz, based on alternating thiazolothiazole and carbazole units was synthesized. The new polymer exhibited a field-effect carrier mobility of up to 3.8 × 10(-3) cm(2) V(-1) s(-1) and bulk heterojunction solar cells made from PCDTTz produced a power conversion efficiency of 4.88% under AM 1.5 G (100 mW cm(-2)) conditions.

Utilizing the N-annulated PDI acceptor PDI–DPP–PDI, a simple air-processed and air-tested organic photovoltaic device fabrication procedure has been established to streamline the screening of donor materials.

Solution‐processed organic solar cells are promising owing to their light weight, ease of processability, low cost, flexibility, and large‐area fabrication. Particularly, small‐molecule active materials have been recently developed using straightforward synthesizing methods, exhibiting the least batch‐to‐batch variation in physical and optoelectronic properties and highly reproducible efficiency. A series of 2D‐BDT‐based active materials with various numbers of benzodithiophene (BDT) units and how the number of 2D‐BDT units influences the construction of a well‐defined interconnected structure are reported. The systematically controlled morphology of the 2D‐BDT material helps achieve a high power‐conversion efficiency (PCE) of 8.56% and a high fill factor of 0.73 without the use of additives. The reduced charge recombination and well‐constructed morphology of this material facilitate a PCE of 7.45% in a 77.8 cm2 rigid module, which is the outstanding performance in large‐area modules.

The room temperature (RT) processability of the photoactive layers in polymer solar cells (PSCs) from halogen‐free solvent along with their highly reproducible power conversion efficiencies (PCEs) and intrinsic thickness tolerance are extremely desirable for the large‐area roll‐to‐roll (R2R) production. However, most of the photoactive materials in PSCs require elevated processing temperatures due to their strong aggregation, which are unfavorable for the industrial R2R manufacturing of PSCs. These limiting factors for the commercialization of PSCs are alleviated by synthesizing random terpolymers with components of (2‐decyltetradecyl)thiophen‐2‐yl)naphtho[1,2‐c:5,6‐c′]bis[1,2,5]thiadiazole and bithiophene substituted with methyl thiophene‐3‐carboxylate (MTC). In contrast to the temperature‐dependent PNTz4T polymer, the resulting random terpolymers (PNTz4T‐MTC) show better solubility, slightly reduced crystallinity and aggregation, and weaker intermolecular interaction, thus enabling PNTz4T‐MTC to be processed at RT from a halogen‐free solvent. Particularly, the PNTz4T‐5MTC‐based photoactive layer exhibits an excellent PCE of 9.66%, which is among the highest reported PCEs for RT and ecofriendly halogen‐free solvent processed fullerene‐based PSCs, and a thickness tolerance with a PCE exceeding 8% from 100 to 520 nm. Finally, large‐area modules fabricated with the PNTz4T and PNTz4T‐5MTC polymer have shown 4.29% and 6.61% PCE respectively, with an area as high as 54.45 cm2 in air.

HfO 2 gate dielectric thin-films were deposited on Si wafers using an atomic-layer deposition (ALD) technique with HfCl4 and either H2O or O3 as the precursor and oxidant, respectively. Although the ALD reactions using either H2O or O3 were successfully confirmed at a deposition temperature of 300 °C, the structural and electrical properties of the HfO2 films grown using the two oxidants were quite different. The stronger oxidation power of the O3 compared to H2O increased the oxygen concentration in the HfO2 film and the rate of interfacial SiO2 formation even at the as-deposited state. Because of the larger oxygen concentration, the decrease in the capacitance density of the film grown with O3 after rapid thermal annealing at 750 °C under N2 atmosphere was slightly larger than that of the HfO2 film grown with H2O. Apart from this weakness, all the other electrical properties, including the fixed charge density, the interface trap density, the leakage current density and the hysteresis in the capacitance–voltage plot of the film grown with O3 were superior to those of the film grown with H2O. Therefore, O3 appears to be a better oxidant for the HfO2 film growth using the ALD method.

A series of small compound materials based on benzodithiophene (BDT) and diketopyrrolopyrrole (DPP) with three different alkyl side chains were synthesized and used for organic photovoltaics. These small compounds had different alkyl branches (i.e., 2-ethylhexyl (EH), 2-butyloctyl (BO), and 2-hexyldecyl (HD)) attached to DPP units. Thin films made of these compounds were characterized and their solar cell parameters were measured in order to systematically analyze influences of the different side chains of compounds on the film microstructure, molecular packing, and hence, charge-transport and recombination properties. The relatively shorter side chains in the small molecules enabled more ordered packing structures with higher crystallinities, which resulted in higher carrier mobilities and less recombination factors; the small molecule with the EH branches exhibited the best semiconducting properties with a power conversion efficiency of up to 5.54% in solar cell devices. Our study suggested that tuning the alkyl chain length of semiconducting molecules is a powerful strategy for achieving high performance of organic photovoltaics.