The microstructural complexity of Li-rich cathode materials has so far hampered understanding the critical link between size, morphology and structural defects with both capacity and voltage fadings that this family of materials exhibits. Li2MnO3 is used here as a model material to extract reliable structure-property relationships that can be further exploited for the development of high-performing and long-lasting Li-rich oxides. A series of samples with microstructural variability have been prepared and thoroughly characterized using the FAULTS software, which allows quantification of planar defects and extraction of average crystallite sizes. Together with transmission electron microscopy (TEM) and density functional theory (DFT) results, the successful application of FAULTS analysis to Li2MnO3 has allowed rationalizing the synthesis conditions and identifying the individual impact of concurrent microstructural features on both voltage and capacity fadings, a necessary step for the development of high-capacity Li-ion cathode materials with enhanced cycle life.

The surface configuration of pristine layered oxide cathode particles for Li-ion batteries significantly affects the electrochemical behavior, which is generally considered to be a thin rock-salt layer in the surface. Unfortunately, aside from its thin nature and spatial location on the surface, the true structural nature of this surface rocksalt layer remains largely unknown, creating the need to understand its configuration and the underlying mechanisms of formation. Using scanning transmission electron microscopy, we have found a correlation between the surface rock-salt formation and the crystal facets on pristine LiNi 0.80 Co 0.15 Al 0.05 O 2 primary particles. It is found that the originally (014̅ ) and ( 003) surfaces of the layered phase result in two kinds of rock-salt reconstructions: the (002) and (111) rock-salt surfaces, respectively. Stepped surface configurations are generated for both reconstructions. The (002) configuration is relatively flat with monatomic steps while the (111) configuration shows significant surface roughening. Both reconstructions reduce the ionic and electronic conductivity of the cathode, leading to a reduced electrochemical performance.

Oxides with the CaFe 2 O 4 -type structure have been predicted as being suitable hosts for reactions of intercalation of light cations such as Li and Mg because of their favorable cationic diffusion. Although Li has been shown to intercalate into the Mn 2 O 4 variant, the key structure property correlations determining function are not fully ascertained. This basic information is needed before attempting the intercalation of divalent cations, which face comparably higher migration barriers. For this purpose, the electrode function of CaFe 2 O 4 -type Li 0.8 Mn 2 O 4 was compared for materials made by a direct high-pressure route or through cation exchange from NaMn 2 O 4 . X-ray diffraction and absorption spectroscopy revealed that, despite having largely the same bulk structure, the presence of surface defects blocked Li + transfer in Li 0.8 Mn 2 O 4 made at high pressure. These defects were not present in the cation-exchanged material, which resulted in highly reversible Li intercalation with very fast kinetics in micrometric crystals. Delithiated electrodes from the cation-exchange synthesis were subsequently reduced in an ionic liquid electrolyte containing Mg 2+ . The process induced topotactic changes in the bulk, strongly suggesting the existence of intercalation, but it is accompanied by severe reactivity with the electrolyte that impedes reversibility. This study uncovers that defects affect the fundamentals of cation intercalation in this novel class of materials. The ability of the cation-exchanged material to conduct fast reactions with Li is consistent with calculated activation energy barriers and creates promise for their use as Mg hosts, provided that novel electrolytes enhanced stability at high potential can be realized.

The complete description of defective structures and their impact on materials behavior is a great challenge due to diculties associated with their reliable characterization in the nanoscale. In this paper density functional theory (DFT) calculations are used to elucidate the solid state nuclear magnetic resonance (NMR) spectra of Li 2 MnO 3 which, combined with X-ray diraction (XRD), provide a full description of disorder in this compound. While XRD allows accurate quantication of planar defects, the use of solid state NMR reveals limited vacancy concentrations that were undetected by XRD as NMR is highly sensitive to the atomic local environments. The combination of these methods is here proven to be highly eective in overcoming the challenges of describing in great detail limited concentrations of disorder in transition metal oxides, providing information about structural variables that are essential to their application.