A series of glycolated polythiophenes for use in organic electrochemical transistors (OECTs) is designed and synthesized, differing in the distribution of their ethylene glycol chains that are tethered to the conjugated backbone. While side chain redistribution does not have a significant impact on the optoelectronic properties of the polymers, this molecular engineering strategy strongly impacts the water uptake achieved in the polymers. By careful optimization of the water uptake in the polymer films, OECTs with unprecedented steady‐state performances in terms of [μC*] and current retentions up to 98% over 700 electrochemical switching cycles are developed.

Organic electrochemical transistors (OECTs) comprised of organic mixed conductors can operate in aqueous, biological media and translate low magnitude ionic fluctuations of biological origin into measurable electrical signals. The growing technological interest in these bio-transducers makes the fundamental understanding of ion-to-electron coupling extremely important for the design of new materials and devices. One crucial aspect in this process that has been so far disregarded is the water taken up by the film during device operation and its effects on device performance. Here, using a series of the same electrolyte with varying ion concentrations, we quantify the amount of water that is incorporated into a hydrophilic p-type organic semiconductor film alongside the dopant anions and investigate structural and morphological changes occurring in the film upon electrochemical doping. We show that infiltration of the hydrated dopant ions into the film irreversibly changes the polymer structure and negatively impacts the efficiency, reversibility and speed of charge generation. When less water is injected into the channel, OECTs exhibit higher transconductance and faster switching speeds. Although swelling is commonly suggested to be a necessity for efficient ion-to-electron transduction, this work uncovers the negative impact of a swollen channel material on the performance of accumulation mode OECTs and lays the foundation for future materials design.

Conjugated polymers that support mixed (electronic and ionic) conduction are in demand for applications spanning from bioelectronics to energy harvesting and storage. To design polymer mixed conductors for high‐performance electrochemical devices, relationships between the chemical structure, charge transport, and morphology must be established. A polymer series bearing the same p‐type conjugated backbone with increasing percentage of hydrophilic, ethylene glycol side chains is synthesized, and their performance in aqueous electrolyte gated organic electrochemical transistors (OECTs) is studied. By using device physics principles and electrochemical analyses, a direct relationship is found between the OECT performance and the balanced mixed conduction. While hydrophilic side chains are required to facilitate ion transport—thus enabling OECT operation—swelling of the polymer is not de facto beneficial for balancing mixed conduction. It is shown that heterogeneous water uptake disrupts the electronic conductivity of the film, leading to OECTs with lower transconductance and slower response times. The combination of in situ electrochemical and structural techniques shown here contributes to the establishment of the structure–property relations necessary to improve the performance of polymer mixed conductors and subsequently of OECTs.

Conjugated polymers achieve redox activity in electrochemical devices by combining redox-active, electronically conducting backbones with ion-transporting side chains that can be tuned for different electrolytes. In aqueous electrolytes, redox activity can be accomplished by attaching hydrophilic side chains to the polymer backbone, which enables ionic transport and allows volumetric charging of polymer electrodes. While this approach has been beneficial for achieving fast electrochemical charging in aqueous solutions, little is known about the relationship between water uptake by the polymers during electrochemical charging and the stability and redox potentials of the electrodes, particularly for electron-transporting conjugated polymers. We find that excessive water uptake during the electrochemical charging of polymer electrodes harms the reversibility of electrochemical processes and results in irreversible swelling of the polymer. We show that small changes of the side chain composition can significantly increase the reversibility of the redox behavior of the materials in aqueous electrolytes, improving the capacity of the polymer by more than one order of magnitude. Finally, we show that tuning the local environment of the redox-active polymer by attaching hydrophilic side chains can help to reach high fractions of the theoretical capacity for single-phase electrodes in aqueous electrolytes. Our work shows the importance of chemical design strategies for achieving high electrochemical stability for conjugated polymers in aqueous electrolytes.

Organic electrochemical transistors (OECTs) are the building blocks of biosensors, neuromorphic devices, and complementary circuits. One rule in the materials design for OECTs is the inclusion of a hydrophilic component in the chemical structure to enable ion transport in the film. Here, it is shown that the ladder-type, side-chain free polymer poly(benzimidazobenzophenanthro line) (BBL) performs significantly better in OECTs than the donor-acceptor type copolymer bearing hydrophilic ethylene glycol side chains (P-90). A combination of electrochemical techniques reveals that BBL exhibits a more efficient ion-to-electron coupling and higher OECT mobility than P-90. In situ atomic force microscopy scans evidence that BBL, which swells negligibly in electrolytes, undergoes a drastic and permanent change in morphology upon electrochemical doping. In contrast, P-90 substantially swells when immersed in electrolytes and shows moderate morphology changes induced by dopant ions. Ex situ grazing incidence wide-angle X-ray scattering suggests that the particular packing of BBL crystallites is minimally affected after doping, in contrast to P-90. BBL's ability to show exceptional mixed transport is due to the crystallites' connectivity, which resists water uptake. This side chain-free route for the design of mixed conductors could bring the n-type OECT performance closer to the bar set by their p-type counterparts.