T he Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) mission landed on Mars on 26 November 2018 in Elysium Planitia 1,2 , 38 years after the end of Viking 2 lander operations. At the time, Viking's seismometer 3 did not succeed in making any convincing Marsquake detections, due to its on-deck installation and high wind sensitivity. InSight therefore provides the first direct geophysical in situ investigations of Mars's interior structure by seismology 1,4. The Seismic Experiment for Interior Structure (SEIS) 5 monitors the ground acceleration with six axes: three Very Broad Band (VBB) oblique axes, sensitive to frequencies from tidal up to 10 Hz, and one vertical and two horizontal Short Period (SP) axes, covering frequencies from ~0.1 Hz to 50 Hz. SEIS is complemented by the APSS experiment 6 (InSight Auxiliary Payload Sensor Suite), which includes pressure and TWINS (Temperature and Winds for InSight) sensors and a magnetometer. These sensors monitor the atmospheric sources of seismic noise and signals 7. After seven sols (Martian days) of SP on-deck operation, with seismic noise comparable to that of Viking 3 , InSight's robotic arm 8 placed SEIS on the ground 22 sols after landing, at a location selected through analysis of InSight's imaging data 9. After levelling and noise assessment, the Wind and Thermal Shield was deployed on sol 66 (2 February 2019). A few days later, all six axes started continuous seismic recording, at 20 samples per second (sps) for VBBs and 100 sps for SPs. After onboard decimation, continuous records at rates from 2 to 20 sps and event records 5 at 100 sps are transmitted. Several layers of thermal protection and very low self-noise enable the SEIS VBB sensors to record the daily variation of the

A planet’s crust bears witness to the history of planetary formation and evolution, but for Mars, no absolute measurement of crustal thickness has been available. Here, we determine the structure of the crust beneath the InSight landing site on Mars using both marsquake recordings and the ambient wavefield. By analyzing seismic phases that are reflected and converted at subsurface interfaces, we find that the observations are consistent with models with at least two and possibly three interfaces. If the second interface is the boundary of the crust, the thickness is 20 ± 5 kilometers, whereas if the third interface is the boundary, the thickness is 39 ± 8 kilometers. Global maps of gravity and topography allow extrapolation of this point measurement to the whole planet, showing that the average thickness of the martian crust lies between 24 and 72 kilometers. Independent bulk composition and geodynamic constraints show that the thicker model is consistent with the abundances of crustal heat-producing elements observed for the shallow surface, whereas the thinner model requires greater concentration at depth.

ol 185 was a typical sol on Mars (a Mars sol is 24 h 39.5 min long, and we number sols starting from landing). The ground acceleration spectrogram recorded by the very broadband (VBB) instrument of SEIS 1-3 (Seismic Experiment for Interior Structure; Fig. 1a) is dominated by the noise produced by the weakly turbulent night-time winds and by the powerful, thermally driven convective turbulence during the day 4. Around 17:00 local mean solar time (lmst), the wind fluctuations die out quite suddenly and the planet remains very quiet into the early night hours. Several distinctive features can be seen every sol on Mars. Lander vibrations activated by the wind appear as horizontal thin lines with frequency varying daily as a result of temperature variations of the lander; almost invisible during quiet hours, they are not excited by seismic events (for example, the lander mode at 4 Hz in Fig. 1a). We also observe a pronounced ambient resonance at 2.4 Hz, strongest on the vertical component, with no clear link to wind strength but excited by all the seismic vibrations at that frequency. The relative excitations of the 2.4 Hz and 4 Hz modes serve as discriminants for the origin of ground vibrations recorded by SEIS, allowing us to distinguish between local vibrations induced by atmospheric or lander activity and more distant sources of ground vibrations. On Sol 185, two weak events can also be spotted in the quiet hours of the early evening, one with a broadband frequency content and a second 80 min later, centred on the 2.4 Hz resonance band (Fig. 1a).

For 2 years, the InSight lander has been recording seismic data on Mars that are vital to constrain the structure and thermochemical state of the planet. We used observations of direct (P and S) and surface-reflected (PP, PPP, SS, and SSS) body-wave phases from eight low-frequency marsquakes to constrain the interior structure to a depth of 800 kilometers. We found a structure compatible with a low-velocity zone associated with a thermal lithosphere much thicker than on Earth that is possibly related to a weak S-wave shadow zone at teleseismic distances. By combining the seismic constraints with geodynamic models, we predict that, relative to the primitive mantle, the crust is more enriched in heat-producing elements by a factor of 13 to 20. This enrichment is greater than suggested by gamma-ray surface mapping and has a moderate-to-elevated surface heat flow.

No abstract

The InSight (Interior Exploration using Seismic Investigations, Geodesy and Heat Transport) mission began collecting high quality seismic data on Mars from February 2019. This manuscript documents the seismicity observed by SEIS, InSight’s seismometer, since this time until the end of March, 2020. Within the InSight project, the Marsquake Service (MQS) is responsible for prompt review of all seismic data collected by InSight, detection of events that are likely to be of seismic origin, and curation and release of seismic catalogues. In the first year of data collection, MQS have identified 465 seismic events that we interpret to be from regional and teleseismic marsquakes. Seismic events are grouped into 2 different event families: the low frequency family are dominated by energy at long period below 1 second, and the high frequency family primarily include energy at and above 2.4~Hz. Event magnitudes, from Mars-specific scales, range from 1.3 to 3.7. A third class of events with very short duration but high frequency bursts have been observed 712 times. These are likely associated with a local source driven by thermal stresses. This paper describes the data collected so far in the mission and the procedures under which MQS operates; summarises the content of the current MQS seismic catalogue; and presents the key features of the events we have observed so far, using the largest events as examples.

On November 26, 2018, NASA's InSight lander successfully touched down on the Martian surface in Elysium Planitia (Figure 1). The scientific goals of InSight are to determine the interior structure, composition, and thermal state of Mars, as well as to document the present-day seismicity and impact rate. To achieve these goals, InSight carried the seismometer package SEIS (Seismic Experiment for Interior Structure) to Mars including a very broadband (VBB) and short period (SP) instrument that cover the seismic bandwidth 0.01-5 Hz (Lognonné et al., 2019). These two instruments are used to locate and classify Marsquakes, to

The instrument package SEIS (Seismic Experiment for Internal Structure) with the three very broadband and three short-period seismic sensors is installed on the surface on Mars as part of NASA's InSight Discovery mission. When compared to terrestrial installations, SEIS is deployed in a very harsh wind and temperature environment that leads to inevitable degradation of the quality of the recorded data. One ubiquitous artifact in the raw data is an abundance of transient one-sided pulses often accompanied by high-frequency spikes. These pulses, which we term "glitches", can be modeled as the response of the instrument to a step in acceleration, while the spikes can be modeled as the response to a simultaneous step in displacement. We attribute the glitches primarily to SEIS-internal stress relaxations caused by the large temperature variations to which the instrument is exposed during a Martian day. Only a small fraction of glitches correspond to a motion of the SEIS package as a whole caused by minuscule tilts of either the instrument or the ground. In this study, we focus on the analysis of the glitch+spike phenomenon and present how these signals can be automatically detected and removed from SEIS's raw data. As glitches affect many standard seismological analysis methods such as receiver functions, spectral decomposition and source inversions, we anticipate that studies of the Martian seismicity as well as studies of Mars' internal structure should benefit from deglitched seismic data. Plain Language Summary The instrument package SEIS (Seismic Experiment for Internal Structure) with two fully equipped seismometers is installed on the surface of Mars as part of NASA's InSight Discovery mission. When compared to terrestrial installations, SEIS is more exposed to wind and daily temperature changes that leads to inevitable degradation of the quality of the recorded data. One consequence is the occurrence of a specific type of transient noise that we term "glitch". Glitches show up in the recorded data as one-sided pulses and have strong implications for the typical seismic data analysis. Glitches can be understood as step-like changes in the acceleration sensed by the seismometers. We attribute them primarily to SEIS-internal stress relaxations caused by the large temperature variations to which the instrument is exposed during a Martian day. Only a small fraction of glitches correspond to a motion of the whole SEIS instrument. In this study, we focus on the detection and removal of glitches and anticipate