The wide-scale implementation of solar and other renewable sources of electricity requires improved means for energy storage. An intriguing strategy in this regard is the reduction of CO2 to CO, which generates an energy rich commodity chemical that can be coupled to liquid fuel production. In this work, we report an inexpensive Bismuth Carbon Monoxide Evolving Catalyst (Bi-CMEC) that can be formed upon cathodic polarization of an inert glassy carbon electrode in acidic solutions containing Bi3+ ions. This catalyst can be used in conjunction with ionic liquids to effect the electrocatalytic conversion of CO2 to CO with appreciable current density at overpotentials below 0.2 V. Bi-CMEC is selective for production of CO, operating with a Faradaic efficiency of approximately 95%. When taken together these correspond to a high energy efficiency for CO production, on par with that which has historically only been observed using expensive silver and gold cathodes.

The development of inexpensive electrocatalysts that can promote the reduction of CO2 to CO with high selectivity, efficiency, and large current densities is an important step on the path to renewable production of liquid carbon-based fuels. While precious metals such as gold and silver have historically been the most active cathode materials for CO2 reduction, the price of these materials precludes their use on the scale required for fuel production. Bismuth, by comparison, is an affordable and environmentally benign metal that shows promise for CO2 conversion applications. In this work, we show that a bismuth–carbon monoxide evolving catalyst (Bi-CMEC) can be formed under either aqueous or nonaqueous conditions using versatile electrodeposition methods. In situ formation of this thin-film catalyst on an inexpensive carbon electrode using an organic soluble Bi3+ precursor streamlines preparation of this material and generates a robust catalyst for CO2 reduction. In the presence of appropriate imidazolium based ionic liquid promoters, the Bi-CMEC platform can selectively catalyze conversion of CO2 to CO without the need for a costly supporting electrolyte. This inexpensive system can catalyze evolution of CO with current densities as high as jCO = 25–30 mA/cm2 and attendant energy efficiencies of ΦCO ≈ 80% for the cathodic half reaction. These metrics highlight the efficiency of Bi-CMEC, since only noble metals have been previously shown to promote this fuel forming half reaction with such high energy efficiency. Moreover, the rate of CO production by Bi-CMEC ranges from approximately 0.1–0.5 mmol·cm−2·h−1 at an applied overpotential of η ≈ 250 mV for a cathode with surface area equal to 1.0 cm2. This CO evolution activity is much higher than that afforded by other non-noble metal cathode materials and distinguishes Bi-CMEC as a superior and inexpensive platform for electrochemical conversion of CO2 to fuel.

The development of affordable electrocatalysts that can drive the reduction of CO2 to CO with high selectivity, efficiency, and large current densities is a critical step on the path to production of liquid carbon-based fuels. In this work, we show that inexpensive triflate salts of Sn(2+), Pb(2+), Bi(3+), and Sb(3+) can be used as precursors for the electrodeposition of CO2 reduction cathode materials from MeCN solutions, providing a general and facile electrodeposition strategy, which streamlines catalyst synthesis. The ability of these four platforms to drive the formation of CO from CO2 in the presence of [BMIM]OTf was probed. The electrochemically prepared Sn and Bi catalysts proved to be highly active, selective, and robust platforms for CO evolution, with partial current densities of jCO = 5-8 mA/cm(2) at applied overpotentials of η < 250 mV. By contrast, the electrodeposited Pb and Sb catalysts do not promote rapid CO generation with the same level of selectivity. The Pb material is only ∼10% as active as the Sn and Bi systems at an applied potential of E = -1.95 V and is rapidly passivated during catalysis. The Sb-comprised cathode material shows no activity for conversion of CO2 to CO under analogous conditions. When taken together, this work demonstrates that 1,3-dialkylimidazoliums can promote CO production, but only when used in combination with an appropriately chosen electrocatalyst material. More broadly, these results suggest that the interactions between CO2, the imidazolium promoter, and the cathode surface are all critical to the observed catalysis.

Ionic liquids (ILs) have been established as effective promoters for the electrocatalytic upconversion of CO2 to various commodity chemicals. Imidazolium ([Im]+) cathode combinations have been reported to selectively catalyze the 2e−/2H+ reduction of CO2 to CO. Recently our laboratory has reported energy-efficient systems for CO production featuring inexpensive bismuth-based cathode materials and ILs comprised of 1,3-dialkylimidazolium cations. As part of our ongoing efforts to understand the factors that drive CO2 reduction at electrode interfaces, we sought to evaluate the catalytic performance of alternative ILs in combination with previously described Bi cathodes. In this work, we demonstrate that protic ionic liquids (PILs) derived from 1,8-diazabicyclo[5.4.0]undec-7-ene (DBU) effectively promote the electrochemical reduction of CO2 to formate (HCOO−) with high selectivity. The use of PILs comprised of the conjugate acid of DBU, [DBU-H]+, efficiently catalyzed the reduction of CO2 to HCOO− (FEFA ≈ 80%) with significant suppression of CO production (FECO ≈ 20%) in either MeCN or MeCN/H2O (95/5) solution. When they were used in combination with [DBU-H]+-based PILs, Bi-based cathodes achieved current densities for CO2 reduction (jtot ≈ 25–45 mA/cm2) that are comparable to or greater than those reported with imidazolium ILs such as [BMIM]PF6. As we demonstrate herein, the selectivity of the 2e− reduction of CO2 toward HCOO− or CO can be dictated through the choice of the IL promoter present in the electrolysis solution, even in cases in which the same electrocatalyst material is studied. These findings highlight the tunability of bismuth/IL systems for the electrochemical reduction of CO2 with high efficiency and rapid kinetics.

Real-time changes in the composition and structure of bismuth electrodes used for catalytic conversion of CO2 into CO were examined via X-ray absorption spectroscopy (including XANES and EXAFS), electrochemical quartz crystal microbalance (EQCM), and in situ X-ray reflectivity (XR). Measurements were performed with bismuth electrodes immersed in acetonitrile (MeCN) solutions containing a 1-butyl-3-methylimidazolium ([BMIM]+) ionic liquid promoter or electrochemically inactive tetrabutylammonium supporting electrolytes (TBAPF6 and TBAOTf). Altogether, these measurements show that bismuth electrodes are originally a mixture of bismuth oxides (including Bi2O3) and metallic bismuth (Bi0) and that the reduction of oxidized bismuth species to Bi0 is fully achieved under potentials at which CO2 activation takes place. Furthermore, EQCM measurements conducted during cyclic voltammetry revealed that a bismuth-coated quartz crystal exhibits significant shifts in resistance (ΔR) prior to the onset of CO2 reduction near −1.75 V vs Ag/AgCl and pronounced hysteresis in frequency (Δf) and ΔR, which suggests significant changes in roughness or viscosity at the Bi/[BMIM]+ solution interface. In situ XR performed on rhombohedral Bi (001) oriented films indicates that extensive restructuring of the bismuth film cathodes takes place upon polarization to potentials more negative than −1.6 V vs Ag/AgCl, which is characterized by a decrease of the Bi (001) Bragg peak intensity of ≥50% in [BMIM]­OTf solutions in the presence and absence of CO2. Over 90% of the reflectivity is recovered during the anodic half-scan, suggesting that the structural changes are mostly reversible. In contrast, such a phenomenon is not observed for thin Bi (001) oriented films in solutions of tetrabutylammonium salts that do not promote CO2 reduction. Overall, these results highlight that Bi electrodes undergo significant potential-dependent chemical and structural transformations in the presence of [BMIM]+-based electrolytes, including the reduction of bismuth oxide to bismuth metal and changes in roughness and near-surface viscosity.

Developing photocatalysts capable of organic oxidations enables the generation of value-added products from biomass feedstocks through visible light irradiation. Through a series of nonaqueous photocatalytic experiments, we have uncovered that CdS nanowires catalyze benzyl alcohol (BnOH) oxidation and 5-hydroxymethylfufural (HMF) oxidation. The rate can be improved by introducing nitrate salts that act as a redox mediator in solution. Specifically, nitrate salts of lithium, magnesium, calcium, and manganese promote the selective photooxidation of BnOH to benzaldehyde on CdS in 70–100% yields at rates up to 13.6 mM h–1, compared to 8% yield at 3 mM h–1 in the absence of a nitrate mediator. Kinetic analysis reveals that, in the absence of nitrate salts, the reaction is first-order with respect to BnOH, while in the presence of nitrate, the reaction is half-order in BnOH. This rate law disparity, along with radical trapping and kinetic isotope experiments, suggests that nitrate-mediated alcohol oxidations proceed through a mechanism involving the catalytic generation of a nitrate radical, NO3 •. The generation of this radical also enables the selective photooxidation of HMF to 2,5-diformylfuran at a rate of 2.6 mM h–1 using CdS nanowires.

Tungsten oxide (WO 3 ) electrodes were synthesized by spin-coating an ammonium metatungstate sol. Instability in photocurrent during water oxidation applications has previously been attributed to formation of destructive peroxide intermediates. Under constant illumination, repeated cycles of poising WO 3 electrodes at 0.98 V vs Ag/AgCl in pH 1 sulfate solution followed by measuring the open-circuit potential for several hours show reversibility in the photocurrent decay. This behavior is attributed to photochromic H x WO 3 generated at low concentration within the electrode, which serves to increase the donor density. The Mott−Schottky analysis of electrochemical impedance spectroscopy measurements on WO 3 electrodes before and after performing the oxygen-evolution reaction (OER) exhibits a decrease in donor density from 2.8 × 10 22 to 6.0 × 10 21 cm −3 with a corresponding 110 mV positive shift in the flat-band potential, indicative of tungsten oxidation during the OER. Tungsten oxidation is corroborated by a decrease in W 5+ signal in the X-ray photoelectron spectroscopy data. Measuring the OER rate by gas chromatography during water oxidation shows concurrent recovery of catalytic activity after resting at open circuit under illumination, illustrating the key role of H x WO 3 during photoelectrocatalysis.

The photo(electro)chemical properties of bulk, nanowire, and chemical bath deposits of cadmium sulfide (CdS) for benzylamine oxidation to N-benzylidenebenzylamine (N-BB) in acetonitrile have been evaluated as a model for the activity and stability of CdS toward selective organic oxidations. CdS photocatalysts selectively deliver N-BB at rates ranging from 5 to 26 mM h −1 . Although CdS is a capable photocatalyst, SEM imaging and XPS analysis reveal significant morphological and compositional changes to the particles upon photolysis in benzylamine. These surface changes and surface sulfide oxidation are accompanied by Cd 2+ leaching and hydrogen sulfide evolution, highlighting both redox and acid−base pathways of nonaqueous CdS corrosion. All facets of corrosion have been linked directly with amine reactivity, as the CdS particles are unaffected by substrate-free photolysis. A series of experiments using N,N-dimethylbenzylamine, 4-N,N-trimethylaniline, and ferrocene show that nonaqueous CdS corrosion is facilitated by acidic reaction intermediates opposed to photogenerated holes. Additionally, water and oxygen are essential components to corrosion, as photoelectrochemistry under dry/air-free conditions displays higher and stable photocurrent density as well as material stability. Finally, CdS nanowires display improved corrosion resistance, suggesting that control of particle morphology and/or electronic structure is essential for developing novel chalcogenide photocatalysts.