This paper describes the introduction of 3-D blade designs into the core compressors for the Rolls-Royce Trent engine with particular emphasis on the use of sweep and dihedral in the rotor designs. It follows the development of the basic ideas in a university research project, through multistage low-speed model testing, to the application to high pressure engine compressors. An essential element of the project was the use of multistage CFD and some of the development of the method to allow the designs to take place is also discussed. The first part of the paper concentrates on the university-based research and the methods development. The second part describes additional low-speed multistage design and testing and the high-speed engine compressor design and test.
This paper describes the introduction of 3D blade designs into the core compressors for the Rolls-Royce Trent engine with particular emphasis on the use of sweep and dihedral in the rotor designs. It follows the development of the basic ideas in a university research project, through multistage low-speed model testing, to the application to high pressure engine compressors. An essential element of the project was the use of multistage CFD and some of the development of the method to allow the designs to take place is also discussed. The first part of the paper concentrates on the university-based research and the methods development. The second part describes additional low-speed multistage design and testing and the high-speed engine compressor design and test.
This paper describes the introduction of 3D blade designs into the core compressors of the Rolls-Royce Trent engine series with particular emphasis on the use of sweep and dihedral in the rotor designs. It follows the development of the basic ideas in a university research project, through multistage low-speed model testing, to their application to the high pressure engine compressor. An essential element of the project was the use of multistage CFD and some of the development of the method to allow the designs to take place is also discussed. Part I of the paper concentrated on the fundamental university-based research and the methods development. Part II describes additional low-speed multistage design and testing and the high-speed engine compressor designs and tests.
Within gas turbines the ability to design shorter aggressive S-shaped ducts is advantageous from a performance and weight saving perspective. However, current design philosophies tend to treat the S-shaped duct as an isolated component, neglecting the potential advantages of integrating the design with the upstream or downstream components. In this paper, such a design concept is numerically developed in which the upstream compressor outlet guide vanes are incorporated into the first bend of the S-shaped duct. Positioning the vane row within the first bend imparts a strong radial gradient to the pressure field within the vane passage. Tangential lean and axial sweep are employed such that the vane geometry is modified to exactly match the resulting inclined static pressure field. The integrated design is experimentally assessed and compared to a conventional nonintegrated design on a fully annular low speed test facility incorporating a single stage axial compressor. Several traverse planes are used to gather five-hole probe data which allow the flow structure to be examined through the rotor, outlet guide vane and within the transition ducts. The two designs employ almost identical duct geometry, but integration of the vane row reduces the system length by 21%. Due to successful matching of the static pressure field, the upstream influence of the integrated vane row is minimal and the rotor performance is unchanged. Similarly, the flow development within both S-shaped ducts is similar such that the circumferentially averaged profiles at duct exit are almost identical, and the operation of a downstream component would be unaffected. Overall system loss remains nominally unchanged despite the inclusion of lean and sweep and a reduction in system length. Finally, the numerical design predictions show good agreement with the experimental data thereby successfully validating the design process.
Within gas turbines the ability to design shorter aggressive S-shaped ducts is advantageous from a performance and weight saving perspective. However, current design philosophies tend to treat the S-shaped duct as an isolated component, neglecting the potential advantages of integrating the design with the upstream or downstream components. In this paper such a design concept is numerically developed in which the upstream compressor outlet guide vanes are incorporated into the first bend of the S-shaped duct. Positioning the vane row within the first bend imparts a strong radial gradient to the pressure field within the vane passage. Tangential lean and axial sweep are employed such that the vane geometry is modified to exactly match the resulting inclined static pressure field. The integrated design is experimentally assessed and compared to a conventional non-integrated design on a fully annular low speed test facility incorporating a single stage axial compressor. Several traverse planes are used to gather five-hole probe data which allow the flow structure to be examined through the rotor, outlet guide vane and within the transition ducts. The two designs employ almost identical duct geometry, but integration of the vane row reduces the system length by 21%. Due to successful matching of the static pressure field, the upstream influence of the integrated vane row is minimal and the rotor performance is unchanged. Similarly the flow development within both S-shaped ducts is similar such that the circumferentially averaged profiles at duct exit are almost identical, and the operation of a downstream component would be unaffected. Overall system loss remains nominally unchanged despite the inclusion of lean and sweep and a reduction in system length. Finally, the numerical design predictions show good agreement with the experimental data thereby successfully validating the design process.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.