No abstract

No abstract

Abstract:With the growth of aviation traffic and the demand for emission reduction, alternative fuels like the so-called electrofuels could comprise a sustainable solution. Electrofuels are understood as those that use renewable energy for fuel synthesis and that are carbon-neutral with respect to greenhouse gas emission. In this study, five potential electrofuels are discussed with respect to the potential application as aviation fuels, being n-octane, methanol, methane, hydrogen and ammonia, and compared to conventional Jet A-1 fuel. Three important aspects are illuminated. Firstly, the synthesis process of the electrofuel is described with its technological paths, its energy efficiency and the maturity or research need of the production. Secondly, the physico-chemical properties are compared with respect to specific energy, energy density, as well as those properties relevant to the combustion of the fuels, i.e., autoignition delay time, adiabatic flame temperature, laminar flame speed and extinction strain rate. Results show that the physical and combustion properties significantly differ from jet fuel, except for n-octane. The results describe how the different electrofuels perform with respect to important aspects such as fuel and air mass flow rates. In addition, the results help determine mixture properties of the exhaust gas for each electrofuel. Thirdly, a turbine configuration is investigated at a constant operating point to further analyze the drop-in potential of electrofuels in aircraft engines. It is found that electrofuels can generally substitute conventional kerosene-based fuels, but have some downsides in the form of higher structural loads and potentially lower efficiencies. Finally, a preliminary comparative evaluation matrix is developed. It contains specifically those fields for the different proposed electrofuels where special challenges and problematic points are seen that need more research for potential application. Synthetically-produced n-octane is seen as a potential candidate for a future electrofuel where even a drop-in capability is given. For the other fuels, more issues need further research to allow the application as electrofuels in aviation. Specifically interesting could be the combination of hydrogen with ammonia in the far future; however, the research is just at the beginning stage.

No abstract

During the prototype shop tests, the Model V84.3A ring combustor gas turbine unexpectedly exhibited a noticeable “humming” caused by self-excited flame vibrations in the combustion chamber for certain operating conditions. The amplitudes of the pressure fluctuations in the combustor were unusually high when compared to the previous experience with silo combustor machines. As part of the optimization program, the humming was investigated and analyzed. To date, combustion instabilities in real, complex combustors cannot be predicted analytically during the design phase. Therefore, and as a preventive measure against future surprises by “humming,” a feedback system was developed which counteracts combustion instabilities by modulation of the fuel flow rate with rapid valves (active instability control, AIC). The AIC achieved a reduction of combustion-induced pressure amplitudes by 86 percent. The Combustion instability in the Model V84.3A gas turbine was eliminated by changes of the combustor design. Therefore, the AIC is not required for the operation of customer gas turbines.

Deterioration of axial compressors is in general a major concern in aircraft engine maintenance. Among other effects, roughness in high-pressure compressor reduces the pressure rise and thus efficiency, thereby increasing the specific fuel consumption of an engine. Therefore, it is important to improve the understanding of roughness on compressor blading and their impact on compressor performance. To investigate the surface roughness of rotor blades of a compressors, different stages of an axial high-pressure compressor and a first-stage blisk (BLade–Integrated–dISK) of a regional aircraft engine is measured by a three-dimensional laser scanning microscope. Fundamental types of roughness structures can be identified: impacts in different sizes, depositions as isotropically distributed single elements with steep flanks and anisotropic roughness structures direct approximately normal to the flow direction. To characterise and quantify the roughness structures in more detail, roughness parameters were determined from the measured surfaces. The quantification showed that the roughness height varies through the compressor depending on the stage, position and the blade side. Overall complex roughness structures of different shape, height and size are detected regardless of the type of the blades.

Abstract:The main contributing factors to unsteady loading of Offshore Wind Turbines (OWT) are wind shear, turbulence, and waves. In the present paper, the turbulence intensity and the wind shear exponent are investigated. Using data from the FINO 1 research platform, these parameters are analyzed and compared with the proposed wind field parameters in the IEC standard 61400-3. Based on this analysis, aeroelastic simulations are performed to determine the effect of wind field parameters on the fatigue and the extreme loads on the rotor blades. For the investigations, the aeroelastic model of a 5 MW OWT is used with a focus on design load cases in an operating state (power production). The fatigue loads are examined by means of the damage-equivalent load-range approach. In order to determine the extreme loads with a recurrence period of 50 years, a peak over threshold extrapolation method and a novel method based on average conditional exceedance rates are used. The results show that the requirements of the IEC standard are very conservative for the design of the rotor blades. Therefore, there could be a large optimization potential for the reduction of weight and cost of the rotor blades.

Turbocharger performance significantly affects the thermodynamic properties of the working fluid at engine boundaries and hence engine performance. Heat transfer takes place under all circumstances during turbocharger operation. This heat transfer affects the power produced by the turbine, the power consumed by the compressor, and the engine volumetric efficiency. Therefore, non-adiabatic turbocharger performance can restrict the engine charging process and hence engine performance. The present research work investigates the effect of turbocharger non-adiabatic performance on the engine charging process and turbo lag. Two passenger car turbochargers are experimentally and theoretically investigated. The effect of turbine casing insulation is also explored. The present investigation shows that thermal energy is transferred to the compressor under all circumstances. At high rotational speeds, thermal energy is first transferred to the compressor and latter from the compressor to the ambient. Therefore, the compressor appears to be “adiabatic” at high rotational speeds despite the complex heat transfer processes inside the compressor. A tangible effect of turbocharger non-adiabatic performance on the charging process is identified at turbocharger part load operation. The turbine power is the most affected operating parameter, followed by the engine volumetric efficiency. Insulating the turbine is recommended for reducing the turbine size and the turbo lag.