Introduction: The current COVID-19 pandemic has caused large shortages in personal protective equipment, leading to hospitals buying their supplies from alternative suppliers or even reusing single-use items. Equipment from these alternative sources first needs to be tested to ensure that they properly protect the clinicians that depend on them. This work demonstrates a test suite for protective face masks that can be realized rapidly and cost effectively, using mainly off-the-shelf as well as 3D printing components. Materials and Methods: The proposed test suite was designed and evaluated in order to assess its safety and proper functioning according to the criteria that are stated in the European standard norm EN149:2001+A1 7. These include a breathing resistance test, a CO2 build-up test, and a penetration test. Measurements were performed for a variety of commercially available protective face masks for validation. Results: The results obtained with the rapidly deployable test suite agree with conventional test methods, demonstrating that this setup can be used to assess the filtering properties of protective masks when conventional equipment is not available. Discussion: The presented test suite can serve as a starting point for the rapid deployment of more testing facilities for respiratory protective equipment. This could greatly increase the testing capacity and ultimately improve the safety of healthcare workers battling the COVID-19 pandemic.
The SARS-CoV-2 pandemic resulted in shortages of production and test capacity of FFP2-respirators. Such facemasks are required to be worn by healthcare professionals when performing aerosol-generating procedures on COVID-19 patients. In response to the high demand and short supply, we designed three models of facemasks that are suitable for local production. As these facemasks should meet the requirements of an FFP2-certified facemask, the newly-designed facemasks were tested on the filtration efficiency of the filter material, inward leakage, and breathing resistance with custom-made experimental setups. In these tests, the facemasks were benchmarked against a commercial FFP2 facemask. The filtration efficiency of the facemask's filter material was also tested with coronavirus-loaded aerosols under physiologically relevant conditions. This multidisciplinary effort resulted in the design and production of facemasks that meet the FFP2 requirements, and which can be produced at local production facilities.
In this paper a first iteration of a new scoliosis brace design and correction strategy is presented using compliant shell mechanisms to create both motion and correction. The motion profile of the human spine was found using a segmented motion capture approach. The brace was designed for a case study using a conceptual ellipsoid design approach. The force controlled correction profile was re-invented using a two fold zero and positive stiffness profile. These force generators were built and validated to prove their zero stiffness characteristic. The kinematic part of the brace was detail designed with the correct order of magnitude and validated through their force-deflection characteristic. The end result was a first iteration of a new brace validated and analysed on some critical components which can form the basis for a future biomechanical study.
Deformability of hydrostatic bearings could potentially increase their application range significantly. When a bearing is made compliant, the film pressure starts to influence the deformation of the support itself. This effect, called compliant-hydrostatic pre-loading, is especially crucial to take into account when designing highly deformable hydrostatic bearings. This work introduces the principle of pressure profile matching to minimize the effect of this pre-loading. A two-dimensional design model is introduced to determine the performance of such an elastic bearing utilizing stiffness profile matching. Additionally, an extension to the model is presented to analyze the basic performance of these type of bearings over small counter surface eccentricities. Finally, an embodiment of such a material distribution is presented utilizing functionally graded materials. These embodiments are analyzed with respect to their failure behavior, showing an improved shear stress and strain energy density distribution with the functionally graded supports when compared with conventional elastic supports.
The SARS-CoV-2 pandemic resulted in shortages of production and test capacity of FFP2-respirators. Such facemasks are required to be worn by healthcare professionals when performing aerosol-generating procedures on COVID-19 patients. In response to the high demand and short supply, we designed three models of facemasks that are suitable for local production. As these facemasks should meet the requirements of an FFP2-certified facemask, the newly-designed facemasks were tested on the filtration efficiency of the filter material, inward leakage, and breathing resistance with custom-made experimental setups. In these tests, the locally-produced facemasks were benchmarked against a commercial FFP2 facemask. Furthermore, the protective capacity of the facemasks was tested for the first time with coronavirus-loaded aerosols under physiologically relevant conditions. This multidisciplinary effort resulted in the design and production of facemasks that meet the FFP2 requirements, and which can be mass-produced at local production facilities.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.