Controlled poly(acrylic acid) homopolymers were synthesized for the first time by direct nitroxide-mediated polymerization of acrylic acid. The polymerizations were performed in 1,4-dioxane solution at 120 °C, using an alkoxyamine initiator based on the N-tert-butyl-N-(1-diethyl phosphono-2,2dimethyl propyl) nitroxide, SG1. The kinetics were controlled by the addition of free nitroxide at the beginning of the polymerization and the optimal amount was 9 mol % with respect to the initiator. In this case, whatever the initiator concentration, all polymerizations exhibited the same rate and conversion reached 85-90% within 5 h. Although the rate constant of propagation of acrylic acid is very large, its reactivity is moderated by a low activation-deactivation equilibrium constant between active macroradicals and SG1-capped dormant chains. Various alkoxyamine concentrations were investigated to target different molar masses. At high initiator concentrations, the number-average molar mass, M n, increased linearly with monomer conversion and followed the theoretical values; the polydispersity indexes ranged between 1.3 and 1.5. At low initiator concentration (high target Mn), a deviation from linearity was observed in the Mn vs conversion plot and was clearly assigned to chain transfer to 1,4-dioxane. From these results, the best experimental conditions to obtain well-defined homopolymers with the minimum amount of dead chains were identified.

This article follows a previous study (Macromolecules 2005, 38, 5485) demonstrating that the nitroxide SG1-mediated polymerization of methyl methacrylate can be achieved at 90 °C with high conversion and high quality of control by introducing a small amount of styrene. In this work, the resulting polymer was characterized and the presence of SG1-based alkoxyamine at the polymer chain-end was identified, supporting the livingness of the macromolecules. In particular, it was shown that the alkoxyamine end group was connected to a single styrene terminal unit and that the methyl methacrylate penultimate unit had a strong effect on the temperature of dissociation. Consequently, the copolymerization of methyl methacrylate with a low molar proportion of styrene could be performed at temperatures below 90 °C. The polymer was also used as an efficient macroinitiator in the polymerization of styrene and n-butyl acrylate, to form methyl methacrylate-based block copolymers.

The structure of “living” poly(n-butyl acrylate) homopolymers prepared via nitroxide-mediated controlled radical polymerization in bulk and in miniemulsion at 112 °C was examined by SEC, NMR, and MALDI−TOF mass spectrometry in order to study the influence of chain transfer to polymer. The absence of detectable terminal unsaturation was confirmed by proton NMR. The branched structure was observed by 13C NMR. MALDI−TOF MS demonstrated that the majority of chains, even at high conversion, had the ideal structure with one initiator fragment and one nitroxide end group. From these results, we concluded that intramolecular chain transfer occurred (presumably by backbiting) and was the predominant mechanism throughout the polymerization at 112 °C.

Methyl methacrylate (MMA) was polymerized in bulk at 70 °C in the presence of an alkoxyamine initiator with low dissociation temperature (the so‐called BlocBuilder™) and increasing amounts of free N‐tert‐butyl‐N‐(1‐diethylphosphono‐2,2‐dimethylpropyl) nitroxide (SG1). Low final monomer conversions were reached, indicating a loss in radical activity due to side reactions such as irreversible homoterminations between the propagating radicals and β‐hydrogen transfer (also called disproportionation) from a propagating radical to a free‐SG1 nitroxide. Proton NMR and MALDI‐TOF mass spectrometry were used to analyze the polymer chain‐ends and to clearly identify the main mechanism of irreversible termination. In particular, it was shown that all polymer chains were terminated by an alkene function in the presence of a large excess of free SG1, meaning that β‐hydrogen transfer from PMMA propagating radicals to the nitroxide SG1 was the major chain‐stopping event. On the other hand, for a low excess of free SG1, the two termination modes coexisted. Kinetic modeling was then performed using the PREDICI software, and the rate constant of β‐hydrogen transfer, kβHtr, was estimated to be 1.69 × 103 L mol−1 s−1 at 70 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6333–6345, 2008