No abstract

Large-area surface-plasmon polariton (SPP) interference lithography is presented, which uses an attenuated total reflection-coupling mode to excite the interference of the SPPs. The interference of the SPPs causes a highly directional intensity range in a finite depth of the electric field, which is good for noncontact. Finite-difference time-domain simulations of the interference on a thin resist layer show that broad-beam illumination with a p-polarized light at a wavelength of 441 nm can produce features as small as 60 nm with high contrast, smaller than lambda/7. Our results illustrate the potential for patterning periodic structures over large areas at low cost.

The chiral structures have displayed some inevitable and fascinating properties in many research fields, such as chemistry, biology, mathematics, and physics. In this Article, we report the use of stepwise glancing angle deposition technology to produce the 3D chiral nanostructures. Through the optimization of deposition parameters (such as the orientation angle of poly styrene spheres (PSs) array, the deposition angle, thickness, and number), a great number of chiral structures have been achieved, and their size depends on the diameter of PS spheres. These chiral structures all can be simulated and predesigned through the use of a 3D geometrical model, which greatly improves the efficiency of this method. In addition, the circular dichroism spectrum shows that these chiral structures own an obvious Cotton effect, indicating their potential application as 3D chiral metamaterials.

The effects of alveolar bone socket geometry and bone-implant contact on implant biomechanics, and resulting strain distributions in bone were investigated. Following extraction of lateral incisors on a cadaver mandible, immediate implants were placed and bone-implant contact area, stability and bone strain were measured. In situ biomechanical testing coupled with micro X-ray microscope (μ-XRM) illustrated less stiff bone-implant complexes (701-822 N/mm) compared with bone-periodontal ligament (PDL)-tooth complexes (791-913 N/mm). X-ray tomograms illustrated that the cause of reduced stiffness was due to reduced and limited bone-implant contact. Heterogeneous elemental composition of bone was identified by using energy dispersive X-ray spectroscopy (EDS). The novel aspect of this study was the application of a new experimental mechanics method, that is, digital volume correlation, which allowed mapping of strains in volumes of alveolar bone in contact with a loaded implant. The identified surface and subsurface strain concentrations were a manifestation of load transferred to bone through bone-implant contact based on bone-implant geometry, quality of bone, implant placement, and implant design. 3D strain mapping indicated that strain concentrations are not exclusive to the bone-implant contact regions, but also extend into bone not directly in contact with the implant. The implications of the observed strain concentrations are discussed in the context of mechanobiology. Although a plausible explanation of surgical complications for immediate implant treatment is provided, extrapolation of results is only warranted by future systematic studies on more cadaver specimens and/or in vivo small scale animal models.

This paper presents the results of experimental and theoretical/computational micro-wrinkles and buckling on the surfaces of stretchable poly-dimethylsiloxane (PDMS) coated with nano-scale Gold (Au) layers. The wrinkles and buckles are formed by the unloading of pre-stretched PDMS/ Au structure after the evaporation of nano-scale Au layers. They are then characterized using atomic force microscopy and scanning electron microscopy. The critical stresses required for wrinkling and buckling are analyzed using analytical models. The possible interfacial cracking that can occur along with film buckling is also studied using finite element simulations of the interfacial crack growth. The implications of the results are discussed for potential applications of microwrinkles and micro-buckles in stretchable electronic structures and biomedical devices.

This paper presents the results of an experimental study of the adhesion between bi-material pairs that are relevant to organic light emitting devices, hybrid organic/inorganic light emitting devices, organic bulk heterojunction solar cells, and hybrid organic/inorganic solar cells on flexible substrates. Adhesion between the possible bi-material pairs is measured using force microscopy (AFM) techniques. These include: interfaces that are relevant to organic light emitting devices, hybrid organic/inorganic light emitting devices, bulk heterojunction solar cells, and hybrid combinations of titanium dioxide (TiO 2) and poly(3-hexylthiophene). The results of AFM measurements are incorporated into the Derjaguin-Muller-Toporov model for the determination of adhesion energies. The implications of the results are then discussed for the design of robust organic and hybrid organic/inorganic electronic devices. V

Whereas buckling can cause type III endoleaks, long-term twisting of a stent-graft was investigated here as a mechanism leading to type V endoleak or endotension. Two experimental device designs supported with Z-stents having strut angles of 35° or 45° were compared to a ringed control under accelerated twisting. Damage to each device was assessed and compared after different durations of twisting, with focus on damage that may allow leakage. Stent-grafts with 35° Z-stents had the most severe distortion and damage to the graft fabric. The 45° Z-stents caused less fabric damage. However, consistent stretching was still seen around the holes for sutures, which attach the stents to the graft fabric. Larger holes may become channels for fluid percolation through the wall. The ringed stent-graft had the least damage observed. Stent apexes with sharp angles appear to be responsible for major damage to the fabrics. Device manufacturers should consider stent apex angle when designing stent-grafts, and ensure their devices are resistant to twisting.

Organic single-crystalline semiconductors with long-range periodic order have attracted much attention for potential applications in electronic and optoelectronic devices due to their high carrier mobility, highly thermal stability, and low impurity content. Molecular doping has been proposed as a valuable strategy for improving the performance of organic semiconductors and semiconductor-based devices. However, a fundamental understanding of the inherent doping mechanism is still a key challenge impeding its practical application. In this study, solid evidence for the "perfect" substitutional doping mechanism of the stacking mode between the guest and host molecules in organic single-crystalline semiconductors using polarized photoluminescence spectrum measurements and first-principles calculations is provided. The molecular host-guest doping is further exploited for efficient color-tunable and even white organic single-crystal-based light-emitting devices by controlling the doping concentration. The clarification of the molecular doping mechanism in organic single-crystalline semiconductor host-guest system paves the way for their practical application in high-performance electronic and optoelectronic devices.