No abstract

The effect of partial surface texturing in the form of parabolic grooves, rectangular grooves, and triangular grooves on the hydrodynamic pressure is investigated in the present work. The dimensionless hydrodynamic pressure generated by the partial surface texturing is obtained by the multigrid method. The effect of the texturing parameters on the dimensionless average pressure is analyzed for a given set of operating parameters. The results indicate that the geometric shape, area density, groove depth, and orientation of the grooves have an obvious influence on the hydrodynamic pressure. However, the groove width has little effect on the dimensionless average pressure. The results of the present work demonstrate that surface texturing design is very important to generate additional hydrodynamic pressure according to the operating parameters of the mechanical components.

Purpose -The purpose of this paper is to investigate a partially textured slider of infinite width with orientation ellipse dimples in liquid application. Design/methodology/approach -In this paper, the pressure distribution of lubrication between a partially textured slider and a smooth sliding slider is calculated by the multi-grid method. For the same dimple area, the influence of the ellipse dimple with geometric parameters, and distribution and orientation on the hydrodynamic lubrication is evaluated in terms of the dimensionless average pressure for a given set of operating parameters. Findings -In the present work, the magnitude of the dimensionless average pressure seems proportional to the slender ratio. Consequently, the slender ratio may be chosen as large as possible based on fabrication techniques. The longer axes of ellipse dimples placed parallel to the direction of sliding always show the better hydrodynamic effect. Furthermore, the results show that the ellipse dimples can greatly improve hydrodynamic effect of partially surface textured slider of infinite width by proper design of these texturing parameters. Originality/value -This paper develops a partial surface texturing infinitely width slider with orientation ellipse dimples for improving hydrodynamic lubrication.

A combination technology of the solid lubricant and the laser surface texturing (LST) can significantly improve the tribological properties of friction pairs. The plate sample was textured by fiber laser and composite lubricant of polyimide (PI) and molybdenum disulfide (MoS 2 ) powders were filled in the microdimples. Sliding friction performances of micron-sized composite lubricant and nano-sized composite lubricant were investigated by ring-plate tribometer at temperatures ranging from room temperature (RT) to 400 C. On the one hand, the results of the micron-sized composite lubricant show that the friction coefficient of the textured surface filled with composite lubricant (TS) exhibits the lowest level and the highest stability compared to a textured surface without solid lubrication, smooth surface without lubrication, smooth surface burnished with a layer of composite solid lubricant. The better dimple density range is 35-46%. The friction coefficients of the sample surface filled with micron-composite solid lubricant with the texture density of 35% are maintained at a low level (about 0.1) at temperatures ranging from RT to 300 C. On the other hand, the results of the nano-sized composite lubricant show that these friction properties are better than those of MoS 2 -PI micron-sized composite. The friction coefficients of MoS 2 -PI-CNTs nano-sized composite solid lubricant are lower than those of the MoS 2 -PI composite lubricant at temperatures ranging from RT to 400 C. In addition, the possible mechanisms involving the synergetic effect of the surface texture and the solid lubricant are discussed in the present work.

Purpose This paper aims to find out the tribological performance and self-lubricating mechanism of the laser-textured surface filled with solid lubricant in rolling friction pair. Design/methodology/approach The textures on the surfaces of GCr15 bearing steel were produced by acousto-optic Q diode-pumped yttrium aluminum garnet laser with the technology of “single pulse one time, repeating at intervals” and filled with composite solid lubricant. The tribology tests were conducted on the MMW-1A universal friction and wear testing machine. Findings It was found that the solid-lubricated micro-textured surface can reduce the friction coefficient effectively. The MoS2/PI composite solid lubricant works better than the single MoS2 solid lubricant, and the ratio of PI/MoS2 + PI at 20 per cent is the best recipe. The friction coefficient of the sample surfaces decreases first and then increases with the increase in texture densities, and a texture density of 19.6 per cent has the best effect on friction reduction. The friction coefficient of the textured surfaces gradually decreases with the increase in both rational speed and load. For the same texture density, the friction coefficient of textured surfaces decreases slightly with the increase in diameter. Furthermore, the mechanism of “rolling-extrusion-accumulation” occurred on the textured surface can collect the solid lubricant, thereby, improve the effect of lubricating and anti-friction. Originality/value The results of the experimental studies demonstrated the application prospect of laser surfaces texturing combined with solid lubricant in rolling friction pair.