Pyrolysis of filmogenic natural polymers gives rise to the formation of films of few-layers defective, undoped, and doped graphenes with low electrical conductivity (3000 to 5000 Ω/sq). For the sake of valorization of biomass wastes, it would be of interest to decrease the density of structural defects in order to increase the conductivity of the resulting few-layers graphene samples. In the present study, analytical and spectroscopic evidence is provided showing that by performing the pyrolysis at the optimal temperature (1100 °C), under a low percentage of H2, a significant decrease in the density of defects related to the presence of residual oxygen can be achieved. This improvement in the quality of the resulting few-layers defective graphene is reflected in a decrease by a factor of about 3 or 5 for alginic acid and chitosan, respectively, of the electrical resistance. Under optimal conditions, few-layers defective graphene films with a resistance of 1000 Ω /sq were achieved. The electrode made of high-quality graphene prepared at 1100 °C under Ar/H2 achieved a H2 production of 3.62 µmol with a positive applied bias of 1.1 V under LED illumination for 16 h.

No abstract

A series of defective graphenes containing or not containing N, B, S and other heteroatoms exhibited general activity as metal-free catalysts for the hydrogenation of CC double bonds by hydrazine in the presence of oxygen.

No abstract

A procedure for the one-step preparation of films of few-layer N-doped graphene on top of nanometric hexagonal boron nitride sheets ((N)graphene/h-BN) based on the pyrolysis at 900 °C under an inert atmosphere of a film of chitosan containing about 20 wt% of ammonium borate salt as a precursor is reported. During the pyrolysis a spontaneous segregation of (N)graphene and boron nitride layers takes place. The films were characterized by optical microscopy that shows a thin graphene overlayer covering the boron nitride layer, the latter showing characteristic cracks, and by XPS measurements at different monitoring angles from 0° to 50° where an increase in the proportion of C vs. B and N was observed. The resulting (N)graphene/h-BN films were also characterized by Raman, HRTEM, SEM, FIB-SEM and AFM. The thickness of the (N)graphene and h-BN layers can be controlled by varying the concentration of precursors and the spin coating rate and is typically below 5 nm. Electrical conductivity measurements using microelectrodes can cause the burning of the graphene layer at high intensities, while lower intensities show that (N)graphene/h-BN films behave as capacitors in the range of positive voltages.

Fe or Co nanoparticles (NPs) and two nanoparticulate Fe‐Co alloys having different Fe/Co atomic ratio with average particle size ranging from 10.9 to 26.5 nm embedded in turbostratic graphitic carbon matrix have been prepared by pyrolysis at 900 °C under inert atmosphere of chitosan powders containing Fe2+ and Co2+ ions in various proportions. The resulting Fe/Co NP@C samples have been evaluated as heterogeneous catalysts for the oxidative C−N coupling of amides and aromatic N−H compounds. It was observed that sequential addition of two aliquots of tert‐butyl hydroperoxide (TBHP) in an excess of N,N‐dimethylacetamide (DMA) as solvent affords the corresponding coupling product in high yields, and the most efficient catalyst was Fe NP@C. Fe NP@C is reusable and exhibits a wide scope. The catalytic activity of Fe is supported by using highly pure Fe salt and by the observation that purposely addition of Cu2+ impurities even plays a detrimental effect on the catalytic activity. Mechanistic studies by quenching with 2,2,6,6‐tetramethylpiperidyl‐1‐oxyl (TEMPO) have shown that the amide radical is the key reaction intermediate, and the role of Fe NP@C is to generate the first radicals by TBHP decomposition.

No abstract

No abstract