Solar-based water sanitation is an environmentally friendly process for obtaining clean water that requires efficient light-to-heat-to-vapour generation. Solar-driven interfacial evaporation has potential, but the inability to control interfacial evaporators for solar tracking limits efficiency at large solar zenith angles and when using optical concentration. Furthermore, clogging affects the efficiency of the device. Here, we create a super-wicking and super-light-absorbing (SWSA) aluminium surface for efficient solar-based water sanitation. The measured evaporation rate exceeds that of an ideal device operating at 100% efficiency, which we hypothesize resulted from a reduced enthalpy of vaporization within the microcapillaries. Limited solar absorber-water contact for water transport minimizes heat losses to bulk water and maximizes heat localization at the SWSA surface. The device can be mounted at any angle on a floating platform to optimize incident solar irradiance and can readily be integrated with commercial solar-thermal systems. With a design that is analogous to bifacial photovoltaic solar panels, we show a 150% increase in efficiency compared with a single-sided SWSA. Given the open capillary channels, the device surface can be easily cleaned and reused. Using the SWSA surface to purify contaminated water, we show a decrease in the level of contaminants to well below the WHO and EPA standards for drinkable water.

Metasurfaces consisting of nanoscale structures are underpinning new physical principles for the creation and shaping of quantum states of light. Multiphoton states that are entangled in spatial or angular domains are an essential resource for many quantum applications; however, their production traditionally relies on bulky nonlinear crystals. We predict and demonstrate experimentally the generation of spatially entangled photon pairs through spontaneous parametric down-conversion from a metasurface incorporating a nonlinear thin film of lithium niobate covered by a silica meta-grating. We measure the correlations of photon pairs and identify their spatial antibunching through violation of the classical Cauchy-Schwarz inequality, witnessing the presence of multimode entanglement. Simultaneously, the photon-pair rate is strongly enhanced by 450 times as compared to unpatterned films because of high-quality-factor resonances. These results pave the way to miniaturization of various quantum devices by incorporating ultrathin metasurfaces functioning as room temperature sources of quantum-entangled photons.

We theoretically investigate the possible increase of the second harmonic generation (SHG) efficiency in silicon compatible waveguides by considering an asymmetrical plasmonic slot waveguide geometry and a χ((2)) nonlinear polymer infiltrating the slot. The needed phase matching condition is satisfied between the fundamental waveguide mode at the fundamental frequency (FF) and second-order waveguide mode at the second harmonic frequency (SHF) by an appropriate design of the waveguide opto-geometrical parameters. The SHG signal generated in our starting waveguide is three orders of magnitude higher than those previously reported for a FF corresponding to λ = 1550 nm. Then, the SHG performance was further improved by increasing the asymmetry of the structure where nonlinear coupling coefficients as large as 292 psm(-1)W(-1/2) are predicted. The device length is shorter than 20 µm and the normalized SHG conversion efficiency comes up to more than 1 × 10(5) W(-1)cm(-2).

Direct femtosecond (fs) laser processing is a maskless fabrication technique that can effectively modify the optical, electrical, mechanical, and tribological properties of materials for a wide range of potential applications. However, the eventual implementation of fs-laser-treated surfaces in actual devices remains challenging because it is difficult to precisely control the surface properties. Previous studies of the morphological control of fs-laser-processed surfaces mostly focused on enhancing the uniformity of periodic microstructures. Here, guided by the plasmon hybridisation model, we control the morphology of surface nanostructures to obtain more control over spectral light absorption. We experimentally demonstrate spectral control of a variety of metals [copper (Cu), aluminium (Al), steel and tungsten (W)], resulting in the creation of broadband light absorbers and selective solar absorbers (SSAs). For the first time, we demonstrate that fs-laser-produced surfaces can be used as high-temperature SSAs. We show that a tungsten selective solar absorber (W-SSA) exhibits excellent performance as a high-temperature solar receiver. When integrated into a solar thermoelectric generation (TEG) device, W-SSA provides a 130% increase in solar TEG efficiency compared to untreated W, which is commonly used as an intrinsic selective light absorber.

Metasurfaces are two-dimensional nanoantenna arrays that can control the propagation of light at will. In particular, plasmonic metasurfaces feature ultrathin thicknesses, ease of fabrication, field confinement beyond the diffraction limit, superior nonlinear properties, and ultrafast performances. However, the technological relevance of plasmonic metasurfaces operating in the transmission mode at optical frequencies is questionable due to their limited efficiency. The state-of-the-art efficiency of geometric plasmonic metasurfaces at visible and near-infrared frequencies, for example, is ≤10%. Here, we report a multipole-interference-based transmission-type geometric plasmonic metasurface with a polarization conversion efficiency that reaches 42.3% at 744 nm, over 400% increase over the state of the art. The efficiency is augmented by breaking the scattering symmetry due to simultaneously approaching the generalized Kerker condition for two orthogonal polarizations. In addition, the design of the metasurface proposed in this study introduces an air gap between the antennas and the surrounding media that confines the field within the gap, which mitigates the crosstalk between meta-atoms and minimizes metallic absorption. The proposed metasurface is broadband, versatile, easy to fabricate, and highly tolerant to fabrication errors. We highlight the technological relevance of our plasmonic metasurface by demonstrating a transmission-type beam deflector and hologram with record efficiencies.

No abstract

The generalized Brewster angle (GBA) is the incidence angle at polarization by reflection for p- or s-polarized light. Realizing an s-polarization Brewster effect requires a material with magnetic response, which is challenging at optical frequencies since the magnetic response of materials at these frequencies is extremely weak. Here, we experimentally realize the GBA effect in the visible using a thin-film absorber system consisting of a dielectric film on an absorbing substrate. Polarization by reflection is realized for both p - and s - polarized light at different angles of incidence and multiple wavelengths. We provide a theoretical framework for the generalized Brewster effect in thin-film light absorbers. We demonstrate hydrogen gas sensing using a single-layer graphene film transferred on a thin-film absorber at the GBA with ∼1 fg/mm 2 aerial mass sensitivity. The ultrahigh sensitivity stems from the strong phase sensitivity near the point of darkness, particularly at the GBA, and the strong light–matter interaction in planar nanocavities. These findings depart from the traditional domain of thin films as mere interference optical coatings and highlight its many potential applications including gas sensing and biosensing.

Water-repellent superhydrophobic (SH) surfaces promise a wide range of applications, from increased buoyancy to drag reduction, but their practical use is limited. This comes from the fact that an SH surface will start to lose its efficiency once it is forced into water or damaged by mechanical abrasion. Here, we circumvent these two most challenging obstacles and demonstrate a highly floatable multifaced SH metallic assembly inspired by the diving bell spiders and fire ant assemblies. We study and optimize, both theoretically and experimentally, the floating properties of the design. The assembly shows an unprecedented floating ability; it can float back to the surface even after being forced to submerge under water for months. More strikingly, the assembly maintains its floating ability even after severe damage and piercing in stark contrast to conventional watercrafts and aquatic devices. The potential use of the SH floating metallic assembly ranges from floating devices and electronic equipment protection to highly floatable ships and vessels.