Looking back on the development of metamaterials in the past 20 years, metamaterials have gradually developed from three-dimensional complex electromagnetic structures to a two-dimensional metasurface with a low profile, during which a series of subversive achievements have been produced. The form of electromagnetic manipulation of the metasurface has evolved from passive to active tunable, programmable, and other dynamic and real-time controllable forms. In particular, the proposal of coding and programmable metasurfaces endows metasurfaces with new vitality. By describing metamaterials through binary code, the digital world and the physical world are connected, and the research of metasurfaces also steps into a new era of digitalization. However, the function switch of traditional programmable metamaterials cannot be achieved without human instruction and control. In order to achieve richer and more flexible function regulation and even higher level metasurface design, the intelligence of metamaterials is an important direction in its future development. In this paper, we review the development of tunable, programmable, and intelligent metasurfaces over the past 5 years, focusing on basic concepts, working principles, design methods, manufacturing, and experimental validation. Firstly, several manipulation modes of tunable metasurfaces are discussed; in particular, the metasurfaces based on temperature control, mechanical control, and electrical control are described in detail. It is demonstrated that the amplitude and phase responses can be flexibly manipulated by the tunable metasurfaces. Then, the concept, working principle, and design method of digital coding metasurfaces are briefly introduced. At the same time, we introduce the active programmable metasurfaces from the following aspects, such as structure, coding method, and three-dimensional far-field results, to show the excellent electromagnetic manipulation ability of programmable metasurfaces. Finally, the basic concepts and research status of intelligent metasurfaces are discussed in detail. Different from the previous programmable metamaterials, which must be controlled by human intervention, the new intelligent metamaterials control system will realize autonomous perception, autonomous decision-making, and even adaptive functional manipulation to a certain extent.
Metamaterials, or metasurfaces, allow the flexible and efficient manipulation of electromagnetic (EM) wave. Although the passive coding metasurfaces have achieved a great deal of functionality, they also need a complex design process. In this paper, we propose Hilbert-coding metasurfaces for flexible and convenient EM regulation by arranging Hilbert-coding metamaterial units of different orders. To demonstrate this behavior, we designed 12 metasurfaces, then fabricated and measured 6 samples. Validation results on 6 Hilbert-coding metasurfaces show the deflection angles of the four single beam patterns obtained are about 21°, 13°, 12°, and 39°, with energy values of 7.75 dB, 7.3 dB, 7.2 dB, and 7.7 dB, respectively, and the deflection angles of the dual-beam patterns are 28.5° and 20° with energy values of 10.05 dB and 11.4 dB, respectively. The results are quite consistent with the simulation data, further confirming the feasibility of our idea. In addition, there are potential applications in Wireless Communications and Radar-imaging, like EM beam scanning and EM field energy distribution control in communication and imaging scenarios.
Combining digital information science with metasurface technology is critical for achieving arbitrary electromagnetic wave manipulation. However, there is a scarcity of contemporary scholarly studies on this subject. In this paper, we propose an Ultraviolet (UV) sensing metasurface for programmable electromagnetic scattering field manipulation by combining light control with a microwave field. The active sensing of UV light and the real-time reaction of the scattering are achieved by integrating four UV sensors on the metasurface. On the metasurface, a UV sensor ML8511 and a voltage driver module are coupled to control each row of the Positive-Intrinsic-Negative (PIN) diodes. Due to the light sensing capability of the UV sensor, the on or off state of the PIN diode integrated into the programmable metasurface can be switched efficiently through the change of light. When the incident wave changes, various discrete data are transmitted to the FPGA. Then the FPGA performs the corresponding voltage distribution to control the state of the PIN diode. Finally, different metasurface coding sequences are generated to realize different electromagnetic functions. As a result, the spatial distribution of sensing light by sensors can be used to determine the electromagnetic field and connect sensing optical information with the microwave field. The simulation and measured results show that this design is feasible. This work provides a dimension for electromagnetic waves modulation.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.