No abstract

In order to simulate the on-site compaction conditions of a Stone Matrix Asphalt (SMA) mixture, The Vertical Vibration Testing Method (VVTM), Superpave Gyratory Compactor (SGC), and Marshall method are used to test the SMA-13 mixture, and the physical and mechanical properties of the asphalt mixture designed by these three methods are tested. Subsequently, the influences of the molding method on the mechanical properties are compared. The influence of vibration compaction time on the volume parameters of the SMA mixture is studied. Following the heavy traffic compaction standards, the vibration compaction time of the SMA mixture is determined. The results show that the densities of the heavy Marshall specimen, VVTM specimen, and SGC specimen are 1.018 times, 1.019 times, and 1.015 times greater than that of the standard Marshall specimen, respectively. The passing rate of the 4.75 mm aggregate of the standard Marshall specimen is 29.9%, and that of the VVTM specimen and SGC specimen is 31.1% and 30.5%, respectively, while that of the heavy Marshall specimen is 34.5%. The mechanical strength of the specimen can be greatly improved as the density increases. On the other hand, by the same compaction work, the mechanical strength of the VVTM specimens can be increased by at least 7% compared with the heavy Marshall specimen. The mechanical strength of the VVTM specimen is increased by at least 22% compared with the standard Marshall specimen. The results also show that under the optimal asphalt-aggregate ratio and the same compaction work, the compressive strength and shear strength of the VVTM specimens are increased by at least 6% and 9%, respectively, compared with the Marshall specimens. In summary, the performance of the asphalt mixture designed by the VVTM is superior, providing a wider choice for future asphalt mixture design.

No abstract

The vertical vibration compaction method (VVCM), heavy compaction method and static pressure method were used to form phyllite specimens with different degrees of weathering. The influence of cement content, compactness, and compaction method on the mechanical properties of phyllite was studied. The mechanical properties of phyllite was evaluated in terms of unconfined compressive strength (Rc) and modulus of resilience (Ec). Further, test roads were paved along an expressway in China to demonstrate the feasibility of the highly weathered phyllite improvement technology. Results show that unweathered phyllite can be used as subgrade filler. In spite of increasing compactness, phyllite with a higher degree of weathering cannot meet the requirements for subgrade filler. With increasing cement content, Rc and Ec of the improved phyllite increases linearly. Rc and Ec increase by at least 15% and 17%, respectively, for every 1% increase in cement content and by at least 10% and 6%, respectively, for every 1% increase in compactness. The higher the degree of weathering of phyllite, the greater the degree of improvement of its mechanical properties.

No abstract

Herein, the effects of the contents of emulsified asphalt, waterborne epoxy resin emulsion, and curing agent on the permeability, bond shear strength, water stability, and aging resistance of epoxy-emulsified asphalt were studied. A formulation of epoxy-emulsified asphalt as a fog-sealing adhesive material was recommended, and a comparison between the fabricated adhesive material and a traditional Chinese fog-sealing adhesive material was conducted to verify the technical performance of the new material. In addition, the strength formation mechanism of the epoxy-emulsified asphalt was revealed via microcosmic analysis. Results show that the curing agent content mainly affects the permeability of epoxy-emulsified asphalt, and the emulsified asphalt content significantly affects the bond shear strength, water stability, and aging resistance. Moreover, the ratio of waterborne epoxy resin emulsion to the curing agent (epoxy ratio) has a certain effect on the bond shear strength. In the recommended formulation (a high-permeability and high-bonding fog-sealing adhesive material, which can be referred to simply as HPBFA), emulsified asphalt accounts for 80% of the total mass of the mixture, and the epoxy ratio is 2:1–3:1. It can improve air permeability, bond shear strength, water stability and aging resistance. The HPBFA-cured material exhibits a continuous three-dimensional network structure, hydrophobic surface, and large contact angle. Furthermore, the initial thermal weight loss temperature of the HPBFA-cured material is significantly higher than the environmental aging temperature. Additionally, the maximum temperature decomposition range is 0–160 °C, indicating improved strength, wear resistance, permeability, and aging resistance of the material.

No abstract

No abstract