Semiconductor-based photocatalysis attracts wide attention because of its ability to directly utilize solar energy for production of solar fuels, such as hydrogen and hydrocarbon fuels and for degradation of various pollutants. However, the efficiency of photocatalytic reactions remains low due to the fast electron-hole recombination and low light utilization. Therefore, enormous efforts have been undertaken to solve these problems. Particularly, properly engineered heterojunction photocatalysts are shown to be able to possess higher photocatalytic activity because of spatial separation of photogenerated electron-hole pairs. Here, the basic principles of various heterojunction photocatalysts are systematically discussed. Recent efforts toward the development of heterojunction photocatalysts for various photocatalytic applications are also presented and appraised. Finally, a brief summary and perspectives on the challenges and future directions in the area of heterojunction photocatalysts are also provided.

A novel and simple method for preparing highly photoactive nanocrystalline F--doped TiO2 photocatalyst with anatase and brookite phase was developed by hydrolysis of titanium tetraisopropoxide in a mixed NH4F−H2O solution. The prepared F--doped TiO2 powders were characterized by differential thermal analysis-thermogravimetry (DTA-TG), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV−vis absorption spectroscopy, photoluminescence spectra (PL), transmission electron microscopy (TEM), and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results showed that the crystallinity of anatase was improved upon F- doping. Moreover, fluoride ions not only suppressed the formation of brookite phase but also prevented phase transition of anatase to rutile. The F--doped TiO2 samples exhibited stronger absorption in the UV−visible range with a red shift in the band gap transition. The photocatalytic activity of F--doped TiO2 powders prepared by this method exceeded that of Degussa P25 when the molar ratio of NH4F to H2O was kept in the range of 0.5−3.

Photoreduction of CO2 into sustainable and green solar fuels is generally believed to be an appealing solution to simultaneously overcome both environmental problems and energy crisis. The low selectivity of challenging multi-electron CO2 photoreduction reactions makes it one of the holy grails in heterogeneous photocatalysis. This Review highlights the important roles of cocatalysts in selective photocatalytic CO2 reduction into solar fuels using semiconductor catalysts. A special emphasis in this review is placed on the key role, design considerations and modification strategies of cocatalysts for CO2 photoreduction. Various cocatalysts, such as the biomimetic, metal-based, metal-free, and multifunctional ones, and their selectivity for CO2 photoreduction are summarized and discussed, along with the recent advances in this area. This Review provides useful information for the design of highly selective cocatalysts for photo­(electro)­reduction and electroreduction of CO2 and complements the existing reviews on various semiconductor photocatalysts.

Recent progress and strategies toward solar water splitting over heterogeneous semiconductors are reviewed and the challenges and future perspectives are suggested.

As a green and sustainable technology, semiconductor-based heterogeneous photocatalysis has received much attention in the last few decades because it has potential to solve both energy and environmental problems. To achieve efficient photocatalysts, various hierarchical semiconductors have been designed and fabricated at the micro/nanometer scale in recent years. This review presents a critical appraisal of fabrication methods, growth mechanisms and applications of advanced hierarchical photocatalysts. Especially, the different synthesis strategies such as two-step templating, in situ template-sacrificial dissolution, self-templating method, in situ template-free assembly, chemically induced self-transformation and post-synthesis treatment are highlighted. Finally, some important applications including photocatalytic degradation of pollutants, photocatalytic H2 production and photocatalytic CO2 reduction are reviewed. A thorough assessment of the progress made in photocatalysis may open new opportunities in designing highly effective hierarchical photocatalysts for advanced applications ranging from thermal catalysis, separation and purification processes to solar cells.

TiO2 thin films were prepared on fused quartz by the liquid-phase deposition (LPD) method from a (NH4)2TiF6 aqueous solution upon addition of boric acid (H3BO3) and calcined at various temperatures. The as-prepared films were characterized with thermogravimetry (TG), Fourier transform infrared spectra (FTIR), X-ray diffraction (XRD), UV−Visible spectrophotometry (UV−Vis), scanning electron microscopy (SEM), photoluminescence spectra (PL), and X-ray photoelectron spectroscopy (XPS), respectively. The photocatalytic activity of the samples was evaluated by photocatalytic decolorization of methyl orange aqueous solution. It was found that the as-prepared TiO2 thin films contained not only Ti and O elements, but also a small amount of F, N, and Si elements. The F and N came from the precursor solution, and the amount of F decreased with increasing calcination temperature. Two sources of Si were identified. One was from the SiF6 2- ions, which were formed by a reaction between the treatment solution and quartz substrate. The other was attributed to the diffusion of Si from the surface of quartz substrate into TiO2 thin film at 700 °C or higher calcination temperatures. With increasing calcination temperature, the photocatalytic activity of the TiO2 thin films gradually increased due to the improvement of crystallization of the anatase TiO2 thin films. At 700 °C, the TiO2 thin film showed the highest photocatalytic activity due to the increasing amount of SiO2 as an adsorbent center and better crystallization of TiO2 in the composite thin film. Moreover, the SiO2/TiO2 composite thin film showed the lowest PL intensity due to a decrease in the recombination rate of photogenerated electrons and holes under UV light irradiation, which further confirms the film with the highest photocatalytic activity at 700 °C. When the calcination temperature is higher than 700 °C, the decrease in photocatalytic activity is due to the formation of rutile and the sintering and growth of TiO2 crystallites resulting in the decrease of surface area.

Artificial photosynthesis of hydrocarbon fuels by utilizing solar energy and CO is considered as a potential route for solving ever-increasing energy crisis and greenhouse effect. Herein, hierarchical porous O-doped graphitic carbon nitride (g-C N ) nanotubes (OCN-Tube) are prepared via successive thermal oxidation exfoliation and curling-condensation of bulk g-C N . The as-prepared OCN-Tube exhibits hierarchically porous structures, which consist of interconnected multiwalled nanotubes with uniform diameters of 20-30 nm. The hierarchical OCN-Tube shows excellent photocatalytic CO reduction performance under visible light, with methanol evolution rate of 0.88 µmol g h , which is five times higher than bulk g-C N (0.17 µmol g h ). The enhanced photocatalytic activity of OCN-Tube is ascribed to the hierarchical nanotube structure and O-doping effect. The hierarchical nanotube structure endows OCN-Tube with higher specific surface area, greater light utilization efficiency, and improved molecular diffusion kinetics, due to the more exposed active edges and multiple light reflection/scattering channels. The O-doping optimizes the band structure of g-C N , resulting in narrower bandgap, greater CO affinity, and uptake capacity as well as higher separation efficiency of photogenerated charge carriers. This work provides a novel strategy to design hierarchical g-C N nanostructures, which can be used as promising photocatalyst for solar energy conversion.

Exploring photocatalysts to promote CO2 photoreduction into solar fuels is of great significance. We develop TiO2/perovskite (CsPbBr3) S-scheme heterojunctions synthesized by a facile electrostatic-driven self-assembling approach. Density functional theory calculation combined with experimental studies proves the electron transfer from CsPbBr3 quantum dots (QDs) to TiO2, resulting in the construction of internal electric field (IEF) directing from CsPbBr3 to TiO2 upon hybridization. The IEF drives the photoexcited electrons in TiO2 to CsPbBr3 upon light irradiation as revealed by in-situ X-ray photoelectron spectroscopy analysis, suggesting the formation of an S-scheme heterojunction in the TiO2/CsPbBr3 nanohybrids which greatly promotes the separation of electron-hole pairs to foster efficient CO2 photoreduction. The hybrid nanofibers unveil a higher CO2-reduction rate (9.02 μmol g–1 h–1) comparing with pristine TiO2 nanofibers (4.68 μmol g–1 h–1). Isotope (13CO2) tracer results confirm that the reduction products originate from CO2 source.