No abstract

No abstract

A systematic study was conducted into the use of metal-assisted chemical etching (MacEtch) to fabricate vertical Si microwire arrays, with several models being studied for the efficient redox reaction of reactants with silicon through a metal catalyst by varying such parameters as the thickness and morphology of the metal film. By optimizing the MacEtch conditions, high-quality vertical Si microwires were successfully fabricated with lengths of up to 23.2 μm, which, when applied in a solar cell, achieved a conversion efficiency of up to 13.0%. These solar cells also exhibited an open-circuit voltage of 547.7 mV, a short-circuit current density of 33.2 mA/cm2, and a fill factor of 71.3% by virtue of the enhanced light absorption and effective carrier collection provided by the Si microwires. The use of MacEtch to fabricate high-quality Si microwires therefore presents a unique opportunity to develop cost-effective and highly efficient solar cells.

We demonstrate novel all-back-contact Si nanohole solar cells via the simple direct deposition of molybdenum oxide (MoOx) and lithium fluoride (LiF) thin films as dopant-free and selective carrier contacts (SCCs). This approach is in contrast to conventionally used high-temperature thermal doping processes, which require multistep patterning processes to produce diffusion masks. Both MoOx and LiF thin films are inserted between the Si absorber and Al electrodes interdigitatedly at the rear cell surfaces, facilitating effective carrier collection at the MoOx/Si interface and suppressed recombination at the Si and LiF/Al electrode interface. With optimized MoOx and LiF film thickness as well as the all-back-contact design, our 1 cm(2) Si nanohole solar cells exhibit a power conversion efficiency of up to 15.4%, with an open-circuit voltage of 561 mV and a fill factor of 74.6%. In particular, because of the significant reduction in Auger/surface recombination as well as the excellent Si-nanohole light absorption, our solar cells exhibit an external quantum efficiency of 83.4% for short-wavelength light (∼400 nm), resulting in a dramatic improvement (54.6%) in the short-circuit current density (36.8 mA/cm(2)) compared to that of a planar cell (23.8 mA/cm(2)). Hence, our all-back-contact design using MoOx and LiF films formed by a simple deposition process presents a unique opportunity to develop highly efficient and low-cost nanostructured Si solar cells.

Transparent conducting electrodes (TCEs) are considered to be an essential structural component of flexible organic solar cells (FOSCs). Silver nanowire (AgNW) electrodes are widely used as TCEs owing to their excellent electrical and optical properties. The fabrication of AgNW electrodes has faced challenges in terms of forming large uniform interconnected networks so that high conductivity and reproducibility can be achieved. In this study, a simple method for creating an intimate contact between AgNWs that uses cold isostatic pressing (CIP) is demonstrated. This method increases the conductivity of the AgNW electrodes, which enables the fabrication of high-efficiency inverted FOSCs that have a power conversion efficiency of 8.75% on flexible polyethylene terephthalate with no short circuiting occurring as the CIP process minimizes the surface roughness of the AgNW electrode. This allows to achieve 100% manufacturing yield of FOSCs. Furthermore, these highly efficient FOSCs are proven to only be 2.4% less efficient even for an extreme bending radius of R ≈ 1.5 mm, compared with initial efficiency.

The authors have demonstrated highly efficient white organic light-emitting diodes (WOLEDs) by using two emissive materials as a dopant, 1,4-bis[2-(7-N-diphenyamino-2-(9,9-diethyl-9H-fluoren-2-yl)) vinyl] benzene (DAF-ph) and iridium(III) bis(5-acetyl-2-phenylpyridinato-N,C2′) acetylacetonate ((acppy)2Ir(acac)). It was found that the OLED fabricated in this study emitted a white color consisting of three primary colors (red, green, and blue). The luminance-voltage (L-V) characteristics of the WOLEDs showed the maximum luminance of 30500cd∕m2 at 14V and the maximum luminous efficiency of 38.0cd∕A, respectively. The CIEx,y coordinates of the WOLED also showed (x=0.33, y=0.40) at 10V.

We demonstrate here an embedded metal electrode for highly efficient organic-inorganic hybrid nanowire solar cells. The electrode proposed here is an effective alternative to the conventional bus and finger electrode which leads to a localized short circuit at a direct Si/metal contact and has a poor collection efficiency due to a nonoptimized electrode design. In our design, a Ag/SiO electrode is embedded into a Si substrate while being positioned between Si nanowire arrays underneath poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), facilitating suppressed recombination at the Si/Ag interface and notable improvements in the fabrication reproducibility. With an optimized microgrid electrode, our 1 cm hybrid solar cells exhibit a power conversion efficiency of up to 16.1% with an open-circuit voltage of 607 mV and a short circuit current density of 34.0 mA/cm. This power conversion efficiency is more than twice as high as that of solar cells using a conventional electrode (8.0%). The microgrid electrode significantly minimizes the optical and electrical losses. This reproducibly yields a superior quantum efficiency of 99% at the main solar spectrum wavelength of 600 nm. In particular, our solar cells exhibit a significant increase in the fill factor of 78.3% compared to that of a conventional electrode (61.4%); this is because of the drastic reduction in the metal/contact resistance of the 1 μm-thick Ag electrode. Hence, the use of our embedded microgrid electrode in the construction of an ideal carrier collection path presents an opportunity in the development of highly efficient organic-inorganic hybrid solar cells.

We designed and fabricated a random-size inverted-pyramid-structured polydimethylsiloxane (RSIPS-PDMS) sticker to enhance the light absorption of solar cells and thus increase their efficiency. The fabricated sticker was laminated onto bare glass and crystalline silicon (c-Si) surfaces; consequently, low solar-weighted reflectance values were obtained for these surfaces (6.88 and 17.2%, respectively). In addition, we found that incident light was refracted at the PDMS-air interface of each RSIPS, which redirected the incident power and significantly increased the optical path length in the RSIPS-PDMS sticker which was 14.7% greater than that in a flat-PDMS sticker. Moreover, we investigated power reflection and propagation through the RSIPS-PDMS sticker using a finite-difference time-domain method. By attaching an RSIPS-PDMS sticker onto both an organic solar cell (OSC) based on a glass substrate and a c-Si solar cell, the power conversion efficiency of the OSC and the c-Si solar cell were increased from 8.57 to 8.94% and from 16.2 to 17.9%, respectively. Thus, the RSIPS-PDMS sticker is expected to be universally applicable to the surfaces of solar cells to enhance their light absorption.