Purpose – This paper aims to present a deflection model to improve positional accuracy of industrial robots. Earlier studies have demonstrated the lack of accuracy of heavy-duty robots when exposed to high external forces. One application where the robot is pushed to its limits in terms of forces is friction stir welding (FSW). This process requires the robot to deliver forces of several kilonewtons causing deflections in the robot joints. Especially for robots with serial kinematics, these deflections will result in significant tool deviations, leading to inferior weld quality. Design/methodology/approach – This paper presents a kinematic deflection model, assuming a rigid link and flexible joint serial kinematics robot. As robotic FSW is a process which involves high external loads and a constant welding speed of usually below 50 mm/s, many of the dynamic effects are negligible. The model uses force feedback from a force sensor, embedded on the robot, and predicts the tool deviation, based on the measured external forces. The deviation is fed back to the robot controller and used for online path compensation. Findings – The model is verified by subjecting an FSW tool to an external load and moving it along a path, with and without deviation compensation. The measured tool deviation with compensation was within the allowable tolerance for FSW. Practical implications – The model can be applied to other robots with a force sensor. Originality/value – The presented deflection model is based on force feedback and can predict and compensate tool deviations online.
The increasing industrial demand for lighter, more complex and multi-material components supports the development of novel joining processes with increased automation and process control. Friction stir welding (FSW) is such a process and has seen a fast development in several industries. This welding technique gives the opportunity of automation and online feedback control, allowing automatic adaptation to environmental and geometrical variations of the component. Weld temperature is related to the weld quality and therefore proposed to be used for feedback control. For this purpose, accurate temperature measurements are required. This paper presents an overview of temperature measurement methods applied to the FSW process. Three methods were evaluated in this work: thermocouples embedded in the tool, thermocouples embedded in the workpiece and the tool-workpiece thermocouple (TWT) method. The results show that TWT is an accurate and fast method suitable for feedback control of FSW.
Friction stir welding (FSW) of non-linear joints receives an increasing interest from several industrial sectors like automotive, urban transport and aerospace. A forcecontrolled robot is particularly suitable for welding complex geometries in lightweight alloys. However, complex geometries including three-dimensional joints, non-constant thicknesses and heat sinks such as clamps cause varying heat dissipation in the welded product. This will lead to changes in the process temperature and hence an unstable FSW process with varying mechanical properties. Furthermore, overheating can lead to a meltdown, causing the tool to sink down into the workpiece. This paper describes a temperature controller that modifies the spindle speed to maintain a constant welding temperature. A newly developed temperature measurement method is used which is able to measure the average tool temperature without the need for thermocouples inside the tool. The method is used to control both the plunging and welding operation. The developments presented here are applied to a robotic FSW system and can be directly implemented in a production setting.
Purpose -Friction stir welding (FSW) is a novel method for joining materials without using consumables and without melting the materials. The purpose of this paper is to present the state of the art in robotic FSW and outline important steps for its implementation in industry and specifically the automotive industry. Design/methodology/approach -This study focuses on the robot deflections during FSW, by relating process forces to the deviations from the programmed robot path and to the strength of the obtained joint. A robot adapted for the FSW process has been used in the experimental study. Two sensor-based methods are implemented to determine path deviations during test runs and the resulting welds were examined with respect to tensile strength and path deviation. Findings -It can be concluded that deflections must be compensated for in high strengths alloys. Several strategies can be applied including online sensing or compensation of the deflection in the robot program. The welding process was proven to be insensitive for small deviations and the presented path compensation methods are sufficient to obtain a strong and defect-free welding joint. Originality/value -This paper demonstrates the effect of FSW process forces on the robot, which is not found in literature. This is expected to contribute to the use of robots for FSW. The experiments were performed in a demonstrator facility which clearly showed the possibility of applying robotic FSW as a flexible industrial manufacturing process.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.