Lignin is a major component of lignocellulosic biomass and as such, it is processed in enormous amounts in the pulp and paper industry worldwide. In such industry it mainly serves the purpose of a fuel to provide process steam and electricity, and to a minor extent to provide low grade heat for external purposes. Also from other biorefinery concepts, including 2nd generation ethanol, increasing amounts of lignin will be generated. Other uses for lignin - apart from fuel production - are of increasing interest not least in these new biorefinery concepts. These new uses can broadly be divided into application of the polymer as such, native or modified, or the use of lignin as a feedstock for the production of chemicals. The present review focuses on the latter and in particular the advances in the biological routes for chemicals production from lignin. Such a biological route will likely involve an initial depolymerization, which is followed by biological conversion of the obtained smaller lignin fragments. The conversion can be either a short catalytic conversion into desired chemicals, or a longer metabolic conversion. In this review, we give a brief summary of sources of lignin, methods of depolymerization, biological pathways for conversion of the lignin monomers and the analytical tools necessary for characterizing and evaluating key lignin attributes.

The conversion of lignin to potentially high-value low molecular weight compounds often results in complex mixtures of monomeric and oligomeric compounds. In this study, a method for the quantitative and qualitative analysis of 40 lignin-derived compounds using ultra-high-performance supercritical fluid chromatography coupled to quadrupole-time-of-flight mass spectrometry (UHPSFC/QTOF-MS) has been developed. Seven different columns were explored for maximum selectivity. Makeup solvent composition and ion source settings were optimised using a D-optimal design of experiment (DoE). Differently processed lignin samples were analysed and used for the method validation. The new UHPSFC/QTOF-MS method showed good separation of the 40 compounds within only 6-min retention time, and out of these, 36 showed high ionisation efficiency in negative electrospray ionisation mode. Graphical abstractA rapid and selective method for the quantitative and qualitative analysis of 40 lignin-derived compounds using ultra-high-performance supercritical fluid chromatography coupled to quadrupole-time-of-flight mass spectrometry (UHPSFC/QTOF-MS) Electronic supplementary materialThe online version of this article (10.1007/s00216-017-0663-5) contains supplementary material, which is available to authorized users.

Kraft lignin is the main source of technically produced lignin. For the development of valuable products based on Kraft lignin, its molecular structure is important. However, the chemical composition of Kraft lignin is still not well known. So far, the analysis of Kraft lignin by mass spectrometry (MS) has been mainly focused on monomeric compounds. Previous MS studies on lignin oligomers (LOs) considered only synthesised LO standards and/or lignins produced by processes other than the Kraft process. Furthermore, published MS methods suffer from using high resolution only in the MS1 stage in multiple-stage tandem MS methods. A high resolution in all MSn stages would provide more detailed information about LO fragmentation pathways. Since lignin samples are complex mixtures of a large number of similar phenolic compounds, the selection of tentative LOs in the MS data is challenging. In this study, we present a method for non-targeted analysis of LOs in Kraft lignin using ultra-high-performance liquid chromatography/high-resolution multiple-stage tandem mass spectrometry (UHPLC/HRMSn). A pre-selection strategy for LOs has been established based on a data-dependent neutral loss MS3 method in combination with a principal component analysis-quadratic discriminant analysis classification model (PCA-QDA). The method was optimised using a design of experiments (DOE) approach. The developed approach improved the pre-selection of tentative LOs in complex mixtures. From 587 detected peaks, 36 peaks were identified as LOs. Graphical abstractᅟ Electronic supplementary materialThe online version of this article (10.1007/s00216-018-1400-4) contains supplementary material, which is available to authorized users.

Lignin is the second most abundant biopolymer in nature and a promising renewable resource for aromatic chemicals. For the understanding of different lignin isolation and conversion processes, the identification of phenolic compounds is of importance. However, given the vast number of possible chemical transformations, the prediction of produced phenolic structures is challenging and a nontargeted analysis method is therefore needed. In this study, a nontargeted analysis method has been developed for the identification of phenolic compounds by using an ultrahigh‐performance supercritical fluid chromatography–high‐resolution multiple stage tandem mass spectrometry method, combined with a Kendrick mass defect‐based classification model. The method is applied to a Lignoboost Kraft lignin (LKL), a sodium lignosulfonate lignin (SLS), and a depolymerized Kraft lignin (DKL) sample. In total, 260 tentative phenolic compounds are identified in the LKL sample, 50 in the SLS sample, and 77 in the DKL sample.

Lignin depolymerisation receives great attention due to the pressing need to find sustainable alternatives to fossil sources for production of fuels and chemicals. In this study, alumina-supported Cu-Mn and Ni-Mo catalysts were tested for oxidative depolymerisation of a technical lignin stream-sodium lignosulphonates-to produce valuable low-molecular-weight aromatics that may be considered for applications in the fuels and chemicals sector. The reactions were performed at elevated temperature and oxygen pressure, and the product mixtures were analysed by size exclusion chromatography, two-dimensional nuclear magnetic resonance spectroscopy and supercritical fluid chromatography mass spectrometry. The best performance was obtained with Cu-Mn/δ-Al 2 O 3 , which was thoroughly characterised before and after use by nitrogen physisorption, scanning electron microscopy, energy dispersive spectroscopy, powder X-ray diffraction, thermal gravimetric analysis, inductively coupled plasma optical emission spectrometry and X-ray photoelectron spectroscopy. Major products identified were vanillin, p-hydroxybenzaldehyde, vanillic acid and p-hydroxybenzoic acid as well as smaller aliphatic aldehydes, acids and lactones.