This article presents a low-order engine model to support model-based control development for mode transitions between spark ignition (SI) and homogeneous charge compression ignition (HCCI) combustion modes in gasoline engines. The modeling methodology focuses on cam switching mode transition strategies wherein the mode is abruptly changed between SI and recompression HCCI via a switch of the cam lift and phasing. The model is parameterized to a wide range of steady-state data which are selected to include conditions pertinent to cam switching mode transitions. An additional HCCI combustion model parameter is augmented and tuned based on transient data from SI to HCCI mode transitions where the conditions can be significantly outside any contained in the baseline steady-state parameterization. An adaptation routine is given which allows transient data be assimilated in online operation to update the augmented parameter and improve SI-HCCI transition predictions. With the baseline steady-state parameterization and augmented mode transition parameter, the model is shown to reproduce both steady-state data and transient performance output time histories from SI-HCCI transitions with considerable accuracy.

This paper describes a model-based feedback control method to transition from spark ignition (SI) to homogeneous charge compression ignition (HCCI) combustion in gasoline engines. The purpose of the control structure is to improve robustness and reduce calibration complexity by incorporating feedback of the engine variables into nonlinear model-based calculations that inherently generalize across operating points. This type of structure is sought as an alternative to prior SI-HCCI transition approaches that involve open-loop calibration of input command sequences that must be scheduled by operating condition. The control architecture is designed for cam switching type SI-HCCI mode transition strategies with practical two-stage cam profile hardware, which previously have only been investigated in a purely open-loop framework. Experimental results on a prototype engine show that the control architecture is able to carry out SI-HCCI transitions across the HCCI load range at 2000 rpm engine speed while requiring variation of only one major set point and three minor set points with operating condition. These results suggest a noteworthy improvement in controller generality and ease of calibration relative to previous SI-HCCI transition approaches.

No abstract

Spark ignition direct injection (SIDI) gasoline engines, especially in downsized boosted engine platforms, are increasing their market share relative to port fuel injection (PFI) engines in U.S., European and Chinese vehicles due to better fuel economy by enabling higher compression ratios and higher specific power output. However, particulate matter (PM) emissions from engines are becoming a concern due to adverse human health and environment effects, and more stringent emission standards. To conduct a PM number and size comparison between SIDI and PFI systems, a 2.0L boosted gasoline engine has been equipped and tested with both systems at different loads, air fuel ratios, spark tim ings, fuel pressures and injection timings for SIDI operation and loads, air fuel ratios and spark timings for PFI operation. Regardless of load, air fuel ratio, spark timing, fuel pressure, and injection timing, particle size distribution from SIDI and PFI is shown to be bimodal, exhibiting nucleation and accumulation mode particles. SIDI produces parti cle numbers that are an order of magnitude greater than PFI. Particle number can be reduced by retarding spark timing and operating the engine lean, both for SIDI and PFI operation. Increasing fuel injection pressure and optimizing injection timing with SIDI also reduces PM emissions. This study provides insight into the differences in PM emis sions from boosted SIDI and PFI engines and an evaluation of PM reduction potential by varying engine operating parameters in boosted SIDI and PFI gasoline engines.

Cyclic variability (CV) in lean homogeneous charge compression ignition (HCCI) combustion at the limits of operation is a known phenomenon, and this work aims at investigating the dominant effects for the cycle evolution at these conditions in a multicylinder engine. Experiments are peiformed in a four-cylinder engine at the operating limits at late phasing of lean HCCI operation with negative valve overlap (nvo). A combtistion analysis method that estimates the utiburned fuel mass on a per-cycle basis is applied on both main combustion and the nvo period revealing and quantifying the dominant effects for the cycle evolution at high CV. The interpretation of the results and comparisons with data from a single-cylinder engine indicate that, at high CV, the evolution of combustion phasing is dominated by low-order deterministic couplings similar to the single-cylinder behavior. Variations, such as air fiow and wall temperature, between cylinders strongly infiuetice the level of CV but the evolution of the combustion phasing is governed by the interactions between engine cycles of the individual cylinders.