We report results of density functional theory (DFT) calculations of a metal-free dye, 5-(4-sulfophenylazo)salicylic acid disodium salt, known as Mordant Yellow 10 (MY-10), used as sensitizer for TiO2dye-sensitized solar cells (DSSCs). Given the need to better understand the behavior of the dyes adsorbed on the TiO2nanoparticle, we studied various single and double deprotonated forms of the dye bound to a TiO2cluster, taking advantage of the presence of the carboxyl, hydroxyl, and sulfonic groups as possible anchors. We discuss various binding configurations to the TiO2substrate and the charge transfer from the pigment to the oxide by means of DFT calculations. In agreement with other reports, we find that the carboxyl group tends to bind in bidentate bridging configurations. The salicylate uses both the carboxyl and hydroxyl substituent groups for either a tridentate binding to adjacent Ti(IV) ions or a bidentate Ti-O binding together with an O-H-O binding, due to the rotation of the carboxyl group out of the plane of the dye. The sulfonic group prefers a tridentate binding. We analyze the propensity for electron transfer of the various dyes and find that for MY-10, as a function of the anchor group, the DSSC performance decreases in the order hydroxyl + carboxyl > carboxyl > sulfonate.

We report results of combined experimental and theoretical studies of dye‐sensitized solar cells (DSSCs) using 5‐(4‐sulfophenylazo)salicylic acid disodium salt, known as Mordant Yellow 10 (MY‐10), as TiO2 sensitizer. We focus on a single dye but vary the solvent and the pH of the solution as well as the photoelectrode preparation conditions to determine the conditions for best photovoltaic conversion efficiency. We found experimentally that the efficiency, measured under standard air mass 1.5 global (AM 1.5G) conditions, was higher in solutions of ethanol than of water, but still small (up to 0.174%), although the fill factor (FF) was large (up to 0.73). Of the dyes in ethanol, MY‐10 in alkaline solution showed the best matching of the solar spectrum but displayed the lowest efficiency. Density functional theory (DFT) calculations provided the optimized geometry, electronic structure, and electronic spectrum of the dye in fully protonated as well as partially and totally deprotonated forms, in solution. The calculated optical spectra are consistent with the experimental data, with strong absorption in the visible range only for the alkaline dye solution. The low device efficiency is very likely related to the weak optical absorption in the visible range. The much higher photovoltaic conversion efficiency of the DSSCs fabricated using acid or roughly neutral pH solutions, corresponding to the protonated and partially deprotonated forms of MY‐10, respectively, is likely caused by the better alignment of the ground state of the dye with the redox level of the electrolyte. The decrease with pH of the dye solution of the short‐circuit current was linked to a weaker charge injection from the excited state of the dye to the conduction band of the oxide, which is correlated with the shifting of the excited state of the dye deeper into the CB edge of the semiconductor. The variation of the open‐circuit voltage with the pH of the solution was linked to the adjustment of the conduction band edge of TiO2, depending on the number of protons transferred from the dye to the oxide surface. Based on our results, we analyze the relative importance of the main criteria that should be met by a dye to be used in a DSSC.

The theoretical study of chrysanthemin (cyanidin 3-glucoside) as a pigment for TiO2-based dye-sensitized solar cells (DSSCs) was performed with the GAUSSSIAN 09 simulation. The electronic spectra of neutral and anionic chrysanthemin molecules were calculated by density functional theory with B3LYP functional and DGDZVP basis set. A better energy level alignment was found for partially deprotonated molecules of chrysanthemin, with the excited photoelectron having enough energy in order to be transferred to the conduction band of TiO2 semiconductor in DSSCs. In addition, we used the raw aqueous extracts of roselle (Hibiscus sabdariffa) calyces as the source of chrysanthemin and the extracts with various pH values were tested in DSSCs. The extracts and photosensitized semiconductor layers were characterized by UV-Vis spectroscopy, and DSSCs based on raw extracts were characterized by current density-voltage measurements.

We report on the fabrication of dye-sensitized solar cells with a TiO2 buffer layer between the transparent conductive oxide substrate and the mesoporous TiO2 film, in order to improve the photovoltaic conversion efficiency of the device. The buffer layer was fabricated by pulsed laser deposition whereas the mesoporous film by the doctor blade method, using TiO2 paste obtained by the sol–gel technique. The buffer layer was deposited in either oxygen (10 Pa and 50 Pa) or argon (10 Pa and 50 Pa) onto transparent conducting oxide glass kept at room temperature. The cross-section scanning electron microscopy image showed differences in layer morphology and thickness, depending on the deposition conditions. Transmission electron microscopy studies of the TiO2 buffer layers indicated that films consisted of grains with typical diameters of 10 nm to 30 nm. We found that the photovoltaic conversion efficiencies, determined under standard air mass 1.5 global (AM 1.5G) conditions, of the solar cells with a buffer layer are more than two times larger than those of the standard cells. The best performance was reached for buffer layers deposited at 10 Pa O2. We discuss the processes that take place in the device and emphasize the role of the brush-like buffer layer in the performance increase.

Active semiconductor layers of TiO2 were synthesized via pulsed laser deposition in He, N2, O2, or Ar to manufacture DSSC structures. As-prepared nanostructured TiO2 coatings grown on FTO were photosensitized by the natural absorption of the N719 (Ruthenium 535-bis TBA) dye to fabricate photovoltaic structures. TiO2 photoanode nanostructures with increased adsorption areas of the photosensitizer (a combination with voluminous media) were grown under different deposition conditions. Systematic SEM, AFM, and XRD investigations were carried out to study the morphological and structural characteristics of the TiO2 nanostructures. It was shown that the gas nature acts as a key parameter of the architecture and the overall performance of the deposited films. The best electro-optical performance was reached for photovoltaic structures based on TiO2 coatings grown in He, as was demonstrated by the short-circuit current (Isc) of 5.40 mA, which corresponds to the higher recorded roughness (of 44 ± 2.9 nm RMS). The higher roughness is thus reflected in a more efficient and deeper penetration of the dye inside the nanostructured TiO2 coatings. The photovoltaic conversion efficiency (η) was 1.18 and 2.32% for the DSSCs when the TiO2 coatings were deposited in O2 and He, respectively. The results point to a direct correlation between the electro-optical performance of the prepared PV cells, the morphology of the TiO2 deposited layers, and the crystallinity features, respectively.