Electrochemical reduction of biomass-derived platform molecules is an emerging route for the sustainable production of fuels and chemicals. However, understanding gaps between reaction conditions, underlying mechanisms, and product selectivity have limited the rational design of active, stable, and selective catalyst systems. In this work, the mechanisms of electrochemical reduction of furfural, an important biobased platform molecule and model for aldehyde reduction, are explored through a combination of voltammetry, preparative electrolysis, thiol-electrode modifications, and kinetic isotope studies. It is demonstrated that two distinct mechanisms are operable on metallic Cu electrodes in acidic electrolytes: (i) electrocatalytic hydrogenation (ECH) and (ii) direct electroreduction. The contributions of each mechanism to the observed product distribution are clarified by evaluating the requirement for direct chemical interactions with the electrode surface and the role of adsorbed hydrogen. Further analysis reveals that hydrogenation and hydrogenolysis products are generated by parallel ECH pathways. Understanding the underlying mechanisms enables the manipulation of furfural reduction by rationally tuning the electrode potential, electrolyte pH, and furfural concentration to promote selective formation of important biobased polymer precursors and fuels.

Tremendous progress has been achieved during the past 20 years on not only improving the yields of carbon nanotubes and move progressively towards their mass production, but also on gaining a profound fundamental understanding of the nucleation and the growth processes. Parameters that influence the yield but also the quality (e.g., microstructure, homogeneity within a batch) are better understood. The influence of the carbon precursor, the reaction conditions, the presence of a catalyst, the chemical and physical status of the latter, and other factors have been extensively studied. The purpose of the present Review is not to list all the experiments reported in the literature, but rather to identify trends and provide a comprehensive summary on the role of selected parameters. The role of the catalyst occupies a central place in this Review as a careful control of the metal particle size, particle dispersion on the support, the metastable phase formed under reaction conditions, its possible reconstruction, and faceting strongly influence the diameter of the carbon nanotubes, their structure (number of walls, graphene sheet orientation, chirality), their alignment, and the yield. The identified trends will be compared with recent observations on the growth of graphene. Recent results on metal-free catalysts will be analyzed from a different perspective.

For many years the scientific community has believed in a promising future for carbon nanotubes for various applications in such diverse fields as polymer reinforcement, adsorption, catalysis, electronics and medicine. Industrial production of carbon nanotubes and -fibers and the subsequent availability and decrease of price, have rendered this vision feasible. In the last years, several carbon nanomaterial products have been marketed by major chemical companies. In this work, we present an extensive characterization of a representative set of commercially available carbon nanomaterials. Special focus has been put on their quality, i.e. presence of metal or carbonaceous impurities but also homogeneity and structural integrity. The observations are of importance for subsequent use in catalysis where the presence of impurities or defects in the nanostructure can dramatically modify the activity of the catalytic material..

The isomerization of glucose to fructose represents a key intermediate step in the conversion of cellulosic biomass to fuels and renewable platform chemicals, namely, 5-hydroxymethyl furfural (HMF), 2,5-furandicarboxylic acid (FDCA), and levulinic acid (LA). Although both Lewis acids and Brønsted bases catalyze this reaction, the basecatalyzed pathway received significantly less attention due to its lower selectivity to fructose and the poor yields achieved (<10%). However, we recently demonstrated that homogeneous organic Brønsted bases present a similar performance (∼31% yield) as Sn-containing beta zeolite, a reference catalyst for this reaction. Herein, we report on the first extensive kinetic and mechanistic study on the organic Brønsted base-catalyzed isomerization of glucose to fructose. Specifically, we combine kinetic experiments performed over a broad range of conditions (temperature: 80−120 °C; pH 9.5−11.5; reactant: glucose, fructose) with isotopic studies and in situ 1 H NMR spectroscopy. Pathways leading to isomerization and degradation of the monosaccharides have been identified through careful experimentation and comparison with previously published data. Kinetic isotope effect experiments were carried out with labeled glucose to validate the rate-limiting step. The ex situ characterization of the reaction products was confirmed using in situ 1 H NMR studies. It is shown that unimolecular (thermal) and bimolecular (alkaline) degradation of fructose can be minimized independently by carefully controlling the reaction conditions. Fructose was produced with 32% yield and 64% selectivity within 7 min.

Fructose is a key intermediate in the conversion of cellulosic biomass to biofuels and renewable platform chemicals. Biomass-derived glucose can be isomerized to fructose using either Lewis acid or Brønsted base catalysts. Lewis acids are typically preferred as alkaline conditions promote a large number of side reactions. It is widely admitted that only low fructose yields, below 10%, are achievable with inorganic bases. Here, fructose was synthesized with 32% yield using commercially available organic amines. Glucose conversion and fructose selectivity were comparable to Lewis acids, which opens new perspectives for the base-catalyzed pathway.

X-ray photoelectron spectroscopy (XPS) is a widely used technique for characterizing the chemical and electronic properties of highly ordered carbon nanostructures, such as carbon nanotubes and graphene. However, the analysis of XPS data—in particular the C 1s region—can be complex, impeding a straightforward evaluation of the data. In this work, an overview of extrinsic and intrinsic effects that influence the C 1s XPS spectra—for example, photon broadening or carbon–catalyst interaction—of various graphitic samples is presented. Controlled manipulation of such samples is performed by annealing, sputtering, and oxygen functionalization to identify different C[BOND]C bonding states and assess the impact of the manipulations on spectral line shapes and their binding energy positions. With high-resolution XPS and XPS depth profiling, the spectral components arising from disordered carbon and surface-defect states can be distinguished from aromatic sp^-2 carbon. These findings illustrate that both spectral line shapes and binding energy components must be considered in the analysis of potentially defective surfaces of carbon materials. The sp^-2 peak, characteristic of aromatic carbon, features a strong asymmetry that changes with the curvature of the sample surface and, thus, cannot be neglected in spectral analysis. The applied deconvolution strategy may provide a simple guideline to obtaining high-quality fits to experimental data on the basis of a careful evaluation of experimental conditions, sample properties, and the limits of the fit procedure

A general method is described for the deposition of metal nanoparticles selectively either inside or outside of carbon nanotubes (CNTs). The method is based on the difference in the interface energies of organic and aqueous solutions with the CNT surface. Because of their lipophilic character, the organic solvent better wets the surface of the nanotubes compared to water and penetrates into the inner volume. The precise control of the volume of each phase allows filling the CNT with the organic phase and covering its outer surface with the aqueous one. Hence, metal nanoparticles can be put with high selectivity either inside or outside the CNT, just by choosing in which solvent the metal precursor is dissolved. SEM, TEM, and 3D-TEM investigations show that a selectivity in localization close to 75% can be reached by this technique. The nanoparticles are homogeneously dispersed and present a narrow size distribution, centered on 5 nm. In this way, one can decorate either the inner or the outer surface of open CNTs, without the need of discriminating the diameter of the opening and without any further step of functionalization than a treatment with nitric acid.

Controlling the charge transfer between a semiconducting catalyst carrier and the supported transition metal active phase represents an elite strategy for fine turning the electronic structure of the catalytic centers, hence their activity and selectivity. These phenomena have been theoretically and experimentally elucidated for oxide supports but remain poorly understood for carbons due to their complex nanoscale structure. Here, we combine advanced spectroscopy and microscopy on model Pd/C samples to decouple the electronic and surface chemistry effects on catalytic performance. Our investigations reveal trends between the charge distribution at the palladium–carbon interface and the metal’s selectivity for hydrogenation of multifunctional chemicals. These electronic effects are strong enough to affect the performance of large (~5 nm) Pd particles. Our results also demonstrate how simple thermal treatments can be used to tune the interfacial charge distribution, hereby providing a strategy to rationally design carbon-supported catalysts.