Infrared (IR) absorption spectroscopy measurements, performed at 300 K and high pressures (27-55 bar) on several prototypes of metal organic framework (MOF) materials, reveal that the MOF ligands are weakly perturbed upon incorporation of guest molecules and that the molecular hydrogen (H(2)) stretch mode is red-shifted (30-40 cm(-1)) from its unperturbed value (4155 cm(-1) for ortho H(2)). For MOFs of the form M(bdc)(ted)(0.5) (bdc = 1,4-benzenedicarboxylate; ted = triethylenediamine), H(2) molecules interact with the organic ligands instead of the saturated metal centers located at the corners of the unit cell. First-principles van der Waals density functional calculations identify the binding sites and further show that the induced dipole associated with the trapped H(2) depends sensitively on these sites. For M(bdc)(ted)(0.5) systems, the strongest dipole moment is of the site that is in the corner of the unit cell and is dominated by the interaction with the benzene ligand and not by the metal center. For MOFs of the M(3)[HCOO](6) type with relatively short ligands (i.e., formate) and 1-D pore structures, there is a weak dependence of H(2) vibrational frequency on the cations, due to a small change in the unit cell dimension. Furthermore, translational states of approximately +/-100 cm(-1) are clearly observed as side bands on the H(2) stretch mode in these 1-D channels interconnected by very small apertures. The H(2) stretch IR integrated areas in all the MOFs considered in this work increase linearly with H(2) pressure, consistent with isotherm measurements performed in similar conditions. However, the IR intensity varies substantially, depending on the number of benzene rings interacting with the H(2) molecules. Finally, there is no correlation between H(2) binding energies (determined by isotherm measurements) and the magnitude of the H(2) stretch shift, indicating that IR shifts are dominated by the environment (organic ligand, metal center, and structure) rather than the strength of the interaction. These results highlight the relevance of IR spectroscopy to determine the type and arrangement of ligands in the structure of MOFs.

Infrared (IR) absorption spectroscopy measurements of molecular hydrogen in MOF-74-M (M = metal center) are performed as a function of temperature and pressure [to 45 kTorr (60 bar) at 300 K, and at lower pressures in the 20-200 K range] to investigate the nature of H(2) interactions with the unsaturated metal centers. A small shift (∼ -30 cm(-1) with respect to the unperturbed H(2) molecule) is observed for the internal stretch frequency of H(2) molecules adsorbed on the metal site at low loading. This finding is in contrast to much larger shifts (∼ -70 cm(-1)) observed in previous studies of MOFs with unsaturated metal centers (including MOF-74) and the general assumption that H(2) stretch shifts depend on adsorption energies (FitzGerald et al., Phys. Rev. B 2010, 81, 104305). We show that larger shifts (∼ -70 cm(-1)) do occur, but only when the next available site ("oxygen" site) is occupied. This larger shift originates from H(2)-H(2) interactions on neighboring sites of the same pore, consistent with the short distance between H(2) in these two sites ∼2.6 Å derived from an analysis of neutron diffraction experiments of D(2)-D(2) at 4 K (Liu et al., Langmuir 2008, 24, 4772-4777). Our results at 77 K and low loading can be explained by a diffusion barrier against pair disruption, which should be enhanced by this interaction. Calculations indicate that the vibrational shifts do not correlate with binding energies and are instead very sensitive to the environment (interaction potential and H(2)-H(2) interactions), which complicates the use of variable temperature IR methods to calculate adsorption energies of specific adsorption sites.

Interface layers between reactive and energetic materials in nanolaminates or nanoenergetic materials are believed to play a crucial role in the properties of nanoenergetic systems. Typically, in the case of Metastable Interstitial Composite nanolaminates, the interface layer between the metal and oxide controls the onset reaction temperature, reaction kinetics, and stability at low temperature. So far, the formation of these interfacial layers is not well understood for lack of in situ characterization, leading to a poor control of important properties. We have combined in situ infrared spectroscopy and ex situ X-ray photoelectron spectroscopy, differential scanning calorimetry, and high resolution transmission electron microscopy, in conjunction with first-principles calculations to identify the stable configurations that can occur at the interface and determine the kinetic barriers for their formation. We find that (i) an interface layer formed during physical deposition of aluminum is composed of a mixture of Cu, O, and Al through Al penetration into CuO and constitutes a poor diffusion barrier (i.e., with spurious exothermic reactions at lower temperature), and in contrast, (ii) atomic layer deposition (ALD) of alumina layers using trimethylaluminum (TMA) produces a conformal coating that effectively prevents Al diffusion even for ultrathin layer thicknesses (∼0.5 nm), resulting in better stability at low temperature and reduced reactivity. Importantly, the initial reaction of TMA with CuO leads to the extraction of oxygen from CuO to form an amorphous interfacial layer that is an important component for superior protection properties of the interface and is responsible for the high system stability. Thus, while Al e-beam evaporation and ALD growth of an alumina layer on CuO both lead to CuO reduction, the mechanism for oxygen removal is different, directly affecting the resistance to Al diffusion. This work reveals that it is the nature of the monolayer interface between CuO and alumina/Al rather than the thickness of the alumina layer that controls the kinetics of Al diffusion, underscoring the importance of the chemical bonding at the interface in these energetic materials.

The main challenge for gas storage and separation in nanoporous materials is that many molecules of interest adsorb too weakly to be effectively retained. Instead of synthetically modifying the internal surface structure of the entire bulk—as is typically done to enhance adsorption—here we show that post exposure of a prototypical porous metal-organic framework to ethylenediamine can effectively retain a variety of weakly adsorbing molecules (for example, CO, CO2, SO2, C2H4, NO) inside the materials by forming a monolayer-thick cap at the external surface of microcrystals. Furthermore, this capping mechanism, based on hydrogen bonding as explained by ab initio modelling, opens the door for potential selectivity. For example, water molecules are shown to disrupt the hydrogen-bonded amine network and diffuse through the cap without hindrance and fully displace/release the retained small molecules out of the metal-organic framework at room temperature. These findings may provide alternative strategies for gas storage, delivery and separation.

Activation of molecular hydrogen is the first step in producing many important industrial chemicals that have so far required expensive noble-metal catalysts and thermal activation. We demonstrate here that aluminium doped with very small amounts of titanium can activate molecular hydrogen at temperatures as low as 90 K. Using an approach that uses CO as a probe molecule, we identify the atomistic arrangement of the catalytically active sites containing Ti on Al(111) surfaces, combining infrared reflection-absorption spectroscopy and first-principles modelling. CO molecules, selectively adsorbed on catalytically active sites, form a complex with activated hydrogen that is removed at remarkably low temperatures (115 K; possibly as a molecule). These results provide the first direct evidence that Ti-doped Al can carry out the essential first step of molecular hydrogen activation under nearly barrierless conditions, thereby challenging the monopoly of noble metals in hydrogen activation.

OATAO is an open access repository that collects the work of Toulouse researchers and makes it freely available over the web where possible. This is an author-deposited version published in : http://oatao.univ-toulouse.fr/ Eprints ID : 16792To link to this article :

No abstract

Alanes are believed to be the mass transport intermediate in many hydrogen storage reactions and thus important for understanding rehydrogenation kinetics for alanates and AlH3. Combining density functional theory (DFT) and surface infrared (IR) spectroscopy, we provide atomistic details about the formation of alanes on the Al(111) surface, a model environment for the rehydrogenation reactions. At low coverage, DFT predicts a 2-fold bridge site adsorption for atomic hydrogen at 1150 cm(-1), which is too weak to be detected by IR but was previously observed in electron energy loss spectroscopy. At higher coverage, steps are the most favorable adsorption sites for atomic H adsorption, and it is likely that the AlH3 molecules form (initially strongly bound to steps) at saturation. With increasing exposures AlH3 is extracted from the step edge and becomes highly mobile on the terraces in a weakly bound state, accounting for step etching observed in previous STM studies. The mobility of these weakly bound AlH3 molecules is the key factor leading to the growth of larger alanes through AlH3 oligomerization. The subsequent decomposition and desorption of alanes is also investigated and compared to previous temperature programmed desorption studies.