A combination of Raman spectroscopy and X-ray diffraction was used to investigate the insertion of ammonia borane in the 5.5 Å diameter pores of the hydrophobic, all-silica zeolite, silicalite-1F in the pressure range up to 4.8 GPa. Insertion and nanoconfinement result in the appearance of new Raman modes, especially in the N–H stretching region and significant changes in the intensities and pressure dependencies of a large number of other modes. Orientational disorder of the −BH3 and −NH3 groups persists to higher pressures in nanoconfined as compared to the bulk ammonia borane. The structure of the recovered sample was determined by single crystal X-ray diffraction. Each pore in the unit cell was found to contain between 2 and 3 molecules of ammonia borane forming single-molecule chains due to the spatial constraints. In situ, high pressure, X-ray powder diffraction indicated that the compressibility of the ammonia borane-silicalite-1F composite is three times lower than that of empty silicalite-1F due to pore filling. These results show that silicalite-1F can be a suitable nanoscaffold for this important chemical hydrogen-storage material.

Ordered mesoporous silica materials were prepared under different pH conditions by using a silicon alkoxide as a silica source and polyion complex (PIC) micelles as the structure-directing agents. PIC micelles were formed by complexation between a weak polyacid-containing double-hydrophilic block copolymer, poly(ethylene oxide)-b-poly(acrylic acid) (PEO-b-PAA), and a weak polybase, oligochitosan-type polyamine. As both the micellization process and the rate of silica condensation are highly dependent on pH, the properties of silica mesostructures can be modulated by changing the pH of the reaction medium. Varying the materials synthesis pH from 4.5 to 7.9 led to 2D-hexagonal, wormlike or lamellar mesostructures, with a varying degree of order. The chemical composition of the as-synthesized hybrid organic/inorganic materials was also found to vary with pH. The structure variations were discussed based on the extent of electrostatic complexing bonds between acrylate and amino functions and on the silica condensation rate as a function of pH.

Proton‐exchange membrane fuel cell vehicles offer a low‐carbon alternative to traditional oil fuel vehicles, but their performances still need improvement to be competitive. Raising their operating temperature to 120 °C will enhance their efficiency but is currently unfeasible due to the poor mechanical properties at high temperatures of the state‐of‐the‐art proton‐exchange membranes consisting of perfluorosulfonic acid (PFSA) ionomers. To address this issue, xx designed composite membranes made of two networks: a mat of hybrid fibers to maintain the mechanical properties filled with a matrix of PFSA‐based ionomer to ensure the proton conductivity. The hybrid fibers obtained by electrospinning are composed of intermixed domains of sulfonated silica and a fluorinated polymer. The inter‐fiber porosity is then filled with a PFSA ionomer to obtain dense composite membranes with a controlled fibers‐to‐ionomer ratio. At 80 °C, these obtained composite membranes show comparable performances to a pure PFSA commercial membrane. At 120 °C however, the tensile strength of the PFSA membrane drastically drop down to 0.2 MPa, while it is maintained at 7.0 MPa for the composite membrane. In addition, the composite membrane shows a good conductivity of up to 0.1 S cm−1 at 120 °C/90% RH, which increases with the ionomer content.

No abstract

Polyacid-functionalized inorganic mesoporous materials have attracted considerable interest as catalysts, permselective molecular sieves, or drug carriers. Despite the great interest, their synthesis into ordered mesostructures incorporating polyacids densely and homogeneously distributed in the mesopores is a challenge. Moreover, their properties as conductors for energy applications remain completely unexplored. Here, we report an efficient, one-shot environmentally friendly synthesis route to prepare ordered mesoporous silica functionalized with strong polyacids, which exhibits excellent proton conductivity. We used polyion electrostatic complex micelles as structure-directing, functionalizing, and pore-generating agents to obtain a material of remarkable textural and functional quality. It presents large and ordered mesopores hosting monodisperse polyacid chains corresponding to a dense and homogeneous functionalization of 1.2 mmol SO3H g SiO2 −1 and a function density of 1 SO 3 H per nm 3 of mesopore volume. Overcoming the performance-limiting inhomogeneities, we designed a superprotonic conductor, while the high value of the conductivity, 0.024 S cm −1 at 363 K/95% relative humidity, was maintained for at least 7 days.

No abstract