Copper nanowires (NWs) with uniform diameters and lengths ranging from several hundreds of nanometers to several micrometers have been prepared with high yield by a simple hydrothermal procedure. The X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDS) analysis data indicate that the copper nanowires are free of any contamination, while the electron diffraction (ED) analysis has revealed the nanowires to be single crystals. The nanowire growth mechanism has also been discussed. Hexadecylamine is the surface stabilizing agent in our method, while glucose facilitates formation of single-crystalline seeds on which the copper nanowires grow. The electrical properties of the as-synthesized copper NWs have also been investigated.
Inkjet deposition is an attractive technology to localize nanomaterials in an area-selective manner on virtually any kind of surfaces. Great advantages of the method are effective usage of materials, low processing temperatures and few required manufacturing steps, thus enabling rapid prototyping and bulk production with reasonably low cost. A number of different electrical devices such as light emitting diodes, transistors and solar cells have already been demonstrated, reflecting the versatility of inkjet printing. In this paper, we collect the contemporary results on inkjet deposited gas sensors and show examples of such gas sensing devices based on surface modified WO 3 nanoparticles for efficient discrimination of various gaseous analytes from sub-ppm up to nearly 0.1% concentration levels in air.
In the present work electrically conductive, flexible, lightweight carbon sponge materials derived from open-pore structure melamine foams are studied and explored. Hydrophobic and hydrophilic surface properties - depending on the chosen treatment conditions - allow the separation and storage of liquid chemical compounds. Activation of the carbonaceous structures substantially increases the specific surface area from ~4 m2g−1 to ~345 m2g−1, while retaining the original three-dimensional, open-pore structure suitable for hosting, for example, Ni catalyst nanoparticles. In turn the structure is rendered suitable for hydrogenating acetone to 2-propanol and methyl isobutyl ketone as well for growing hierarchical carbon nanotube structures used as electric double-layer capacitor electrodes with specific capacitance of ~40 F/g. Mechanical stress-strain analysis indicates the materials are super-compressible (>70% volume reduction) and viscoelastic with excellent damping behavior (loss of 0.69 ± 0.07), while piezoresistive measurements show very high gauge factors (from ~20 to 50) over a large range of deformations. The cost-effective, robust and scalable synthesis - in conjunction with their fascinating multifunctional utility - makes the demonstrated carbon foams remarkable competitors with other three-dimensional carbon materials typically based on pyrolyzed biopolymers or on covalently bonded graphene and carbon nanotube frameworks.
Low-temperature thermal chemical vapor deposition (thermal CVD) synthesis of multi-walled carbon nanotubes (MWCNTs) was studied using a large variety of different precursor compounds. Cyclopentene oxide, tetrahydrofuran, methanol, and xylene:methanol mixture as oxygen containing heteroatomic precursors, while xylene and acetylene as conventional hydrocarbon feedstocks were applied in the experiments. The catalytic activity of Co, Fe, Ni, and their bi-as well as tri-metallic combinations were tested for the reactions. Low-temperature CNT growth occurred at 400 8C when using bi-metallic Co-Fe and tri-metallic Ni-Co-Fe catalyst (on alumina) and methanol or acetylene as precursors. In the case of monometallic catalyst nanoparticles, only Co (both on alumina and on silica) was found to be active in the low temperature growth (below 500 8C) from oxygenates such as cyclopentene oxide and methanol. The structure and composition of the achieved MWCNTs products were studied by scanning and transmission electron microscopy (SEM and TEM) as well as by Raman and X-ray photoelectron spectroscopy (XPS) and by X-ray diffraction (XRD). The successful MWCNT growth below 500 8C is promising from the point of view of integrating MWCNT materials into existing IC fabrication technologies.
In this work, we demonstrate the solution processing of optical and electrochemical dye sensors based on 4-(dioctylamino)-4 0 -(trifluoroacetyl)azobenzene and its application in sensing different amine compounds.Distinct optical response of the sensors exposed to ammonia, tetramethylammonium hydroxide, ethylamine, cadaverine and putrescine (typical compounds upon the decomposition of proteins) is observed. Incorporation of inkjet deposited thin films of the dye as sensors in food packages of ground meat and salmon is found as a feasible route to detect the appearance of biogenic amines produced by the degrading food products. Furthermore, we demonstrate an electrochemical amine sensor based on (trifluoroacetyl)azobenzene dye added in carbon nanotube-Nafion® composites. The electrochemical sensor exploits the reaction between the dye and amines to detect amines in electrolytes, while the carbon nanotubes provide large surface for adsorption and also provide a percolating electrical network for allowing efficient charge transfer at the electrode electrolyte interface. Scheme 1 Bonding reaction of 4-(dioctylamino)-4 0 -(trifluoroacetyl)azobenzene and amine. 4688 | J. Mater. Chem. A, 2015, 3, 4687-4694 This journal is
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.